background image

 

 
 

     

 

 

           
 

 

3.  Remove driver-side kick plate. 

 

 

 

a)  Use 4mm screwdriver to release center  

 

      

     of plastic push-pin. 

 
 

 

b)  Grasp kick plate at rear and pull out  

 

      

     towards passenger-side of vehicle.   

 

 

     

(Fig. 1-4) 

 
 
 
 
 
 
 
 
 
 

4.  Loosen driver-side door seal past top 

 

     of A-pillar.  (Fig. 1-5) 

 
 
 
 
 
 
 
 
 
 
 
 

5.  Remove A-pillar trim. 

 
 
 

 

 

a)  Pull out top of A-pillar trim towards  

     

 

     

     passenger-side of vehicle until A-pillar push-pin  

 

 

     connector is fully extended.  

(Fig.  1-6) 

 

b)  Pull A-pillar trim towards the rear of the    

vehicle to release the base and to slide upwards 
and off from A-pillar push-pin connector.   

(Fig.  1-6)

 

 

 

 

6.  Remove OE mirror. 

 

 

 

a)  Insert fiberstick between bottom of mirror mount 

 

 

     and windshield glass.  

(Fig. 1-7)

 

 
 

 

b)  Push fiberstick up into mount to disengage  

 

 

      locking tab.  Pull up while gently wiggling mirror 

 

 

      to remove.

 

 
 
 

 
 
 
 
 

Push-pin 

 

Fig.  1-4 

 
 

 

 
 
 

 

 
 
 
 
 
 
 

 

 

Fig.  1-5 

 
 
 

CAUTION 

A-pillar  

  Push-pin 

Connector 

Fig.  1-6 

 
 
 

CAUTION 

 
 
 

Do not use excessive force.  A-pillar connector could be damaged. 

 
 
 
 
 
 
 

Fig.  1-7 

 
 
 
 
 
 
 
 
 
 
 

Page 3 of 8       

                                    

Revision A

                                                                                   550-0336 

Summary of Contents for 0000-8C-Z02









Reviews: