Maytag MLE24PDAYW Installation Instructions Manual Download Page 19

19

19

  OPTIONS TO USE IF SPECIAL PRICING IS SELECTED (continued):

SPECIAL PRICE START HOUR 

NOTE:

 Uses military time – 24 hr. clock.

This is the start hour, 0–23 hours. Select START  

HOUR by pressing the WHITES AND COLORS key 

pad.

g

   Press the PERM. PRESS key pad once to advance to next code.

SPECIAL PRICE STOP HOUR 

NOTE:

 Uses military time – 24 hr. clock.

This is the stop hour; 0–23 hours. Select STOP HOUR 

by pressing the WHITES AND COLORS key pad.

g

   Press the PERM. PRESS key pad once to advance to next code.

SPECIAL PRICE DAY

This represents the day of the week and whether 

special pricing is selected for that day. A number 

followed by “0” indicates no selection that particular 

day (9.10). A number followed by an “S” indicates 

selected for that day (9.1S). 
Days of the week (1–7) can be chosen by pressing the 

WHITES AND COLORS key pad. Press DELICATES  

key pad once to select special pricing for each day 

chosen.
When exiting setup code “9.,” the display must show 

current day of week:
  DISPLAY 

DAY OF WEEK 

CODE (selected)

 

10 

Day 1 = Sunday 

1S

 

20 

Day 2 = Monday 

2S

 

30 

Day 3 = Tuesday 

3S

 

40 

Day 4 = Wednesday 

4S

 

50 

Day 5 = Thursday 

5S

 

60 

Day 6 = Friday 

6S

 

70 

Day 7 = Saturday 

7S

g

   Press the PERM. PRESS key pad once to advance to next code.

7. 0 0 

7. 0 0

 CODE 

EXPLANATION

8. 0 0 

8. 0 0

9. 1 0

9. 1 0

VAULT VIEWING OPTION

This option is either SELECTED “ON” or 

NOT SELECTED “OFF.”
Not Selected “OFF.”
Selected “ON.” Press DELICATES key pad once for 

this selection. When selected, the money and/or cycle 

counts will be viewable (if counting is selected) when 

the coin box is removed.

g

   Press the PERM. PRESS key pad once to advance to next code.

VALUE OF COIN 1

This represents the value of coin 1 in number of 

nickels: 05 = $0.25.
By pressing the WHITES AND COLORS key pad you 

have the option of 1–199 nickels.

g

   Press the PERM. PRESS key pad once to advance to next code.

VALUE OF COIN 2

This represents the value of coin 2 in number of 

nickels: 20 = $1.00.
By pressing the WHITES AND COLORS key pad you 

have the option of 1–199 nickels.
PR MODELS ONLY: For PR models using Enhanced 

Debit, this field represents the value of top off in  

nickels.
PR MODELS: Factory preset for $0.25.

g

   Press the PERM. PRESS key pad once to advance to next code.

A. 0 0 

A. 0 0  

A.S C  

6. 0 5 
6. 0 5   

C. 2 0 
C. 2 0 

 CODE 

EXPLANATION

COIN SLIDE OPTION

This option is either SELECTED “ON” or 

NOT SELECTED “OFF.”
Not Selected “OFF.”
Selected “ON.” 
Press the DELICATES key pad 3 consecutive times 

for this selection. When coin slide mode is selected, 

set “b.” equal to value of slide in nickels. Set “606” 

(REGULAR CYCLE PRICE)  and “3.06” (SPECIAL 

CYCLE PRICE) to number of slide operations. 

NOTE:

 If the installer sets up “CS” on a coin drop 

model, it will not register coins.

g

   Press the PERM. PRESS key pad once to advance to next 

code.

ADD COINS OPTION

This option is either SELECTED “ON” or NOT 

SELECTED “OFF.” This option causes the customer 

display to show the number of coins (coin 1) to enter, 

rather than the dollars-and-cents amount.
Not Selected “OFF.”
Selected “ON.” 
Press the DELICATES keypad 3 consecutive times for 

this selection.
PR MODELS ONLY: In enhanced debit mode, this 

option is not selectable.

g

   Press the PERM. PRESS key pad once to advance to next 

code.

COIN/DEBIT OPTION

Both coin & debit selected.
Coins selected, debit disabled.                                          

Press DELICATES key pad for this selection.
Debit Card selected, coins disabled.  

Press DELICATES key pad for this selection.
Enhanced Debit is self-selected when a Generation 2 

card reader is installed in the dryer. The “Ed” option 

cannot be manually selected or deselected.

g

   Press the PERM. PRESS key pad once to advance to next 

code.

PRICE SUPPRESSION OPTION

This option is either SELECTED “ON” 

OR NOT SELECTED “OFF.” This option causes the 

customer display to show “AVAILABLE” or “ADD” 

rather than the amount of money to add. (Used mainly 

in debit installations.)
Not Selected “OFF.”
Selected “ON.” Press the DELICATES key pad once for 

this selection.

g

   Press the PERM. PRESS key pad once to advance to next 

code.

CLEAR ESCROW OPTION

This option is either SELECTED “ON” 

OR NOT SELECTED “OFF.” When selected, money 

held in escrow for 30 minutes without further escrow  

or cycle activity will be cleared.
Selected “ON.”
Not sele cted “OFF.” Press the DELICATES key pad 

once for this selection.

g

   Press the PERM. PRESS key pad once to advance to next 

code.

PENNY INCREMENT OFFSET

This represents the penny increment price offset 

used in Generation 2 (Enhanced Debit) PR 

models. Choose from 0–4 pennies by pressing the 

WHITES AND COLORS key pad.

g

   Press the PERM. PRESS key pad once to advance to next 

code.

8. 0 0 

E. 0 0 

E. 0 0  

E.A C  

8. 0 0 

8.

C S 

J.C 8 

L. 0 0 

L. 0 0  

L.P S  

J.C 8 

J.C 8 

J.C 8 

J.E 8 

8.

C E 

8.

C E

 

8.0 0 

0. 0 0  
0. 0 0  

Summary of Contents for MLE24PDAYW













































Reviews: