Maytag LD10D2 Service Manual Download Page 14

Page: 14 / 46

16023053 Rev. 0

Dial and Electronic Models
Oven operates with little or no heat.

Display shows all digits programmed, but does not start cooking when the START pad is
pressed.

Troubleshooting Procedures (Electronic Models)

Output

performance

is low.

Check the power

supply voltage.

Lower than

90% of rated

voltage.

Decrease in

supply voltage

under load.

Customer must

contact local

power

company or

qualified

electrician.

Normal

Disconnect wire leads

from relay RY2 and

verify on and off times.

Abnormal

Normal

Failed

controller.

Replace

controller.

Abnormal

Failed

magnetron

Replace

magnetron.

Measure the

output power.

Time does not

count down after

START pad is

pressed.

Check continuity of

secondaryswitch

with door closed.

Continuity

Malfunction of

secondary

switch.

Replace the

secondary

switch.

Continuity

Check connection

between CN1

connector and

c.ontroller.

Continuity

Failed

controller.

Replace

controller.

Loose

connection.

Repair

connection.

Abnormal

Failed oven

light.

Replace oven

light.

Oven light or fan

motor does not

operate.

Check oven light.

Normal

Check fan motor.

Abnormal

Failed fan

motor.

Replace fan

motor.

Summary of Contents for LD10D2















































Search results

Summary of Contents for LD10D2

Reviews:

Related manuals for LD10D2

Brands by name

Popular brands

Maytag LD10D2, Service Manual

Search results

Summary of Contents for LD10D2

Reviews:

Related manuals for LD10D2

Brands by name

Popular brands