background image

6

STACKED WASHER/DRYER DISPOSAL

This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment 

(WEEE).

By ensuring this product is disposed of correctly, you will help avoid potential negative consequences for the environment 

and human health, which could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be 

treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical 

and electronic equipment.

Disposal must be carried out in accordance with local environmental regulations for waste disposal.

For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, 

your household waste disposal service or the shop where you purchased the product.

MODEL NOMENCLATURE:

MLG

 – Maytag Stacked Laundry Gas Dryer   

PD

 – Electronic Control – Coin Drop Enabled

22

 – Stacked Washer/Dryer Model   

 

PN

 – Electronic Control – Non-Pay

 

  

PR - 

Electronic Control - Card Ready

n

  See “Electrical Requirements” section for 

earthing instructions.

n

  Adequate ventilation has to be provided to 

avoid the back-flow of gases into the room 

from appliances burning fuels, including  

open fires.

n

  The new hose-sets supplied with the 

appliance are to be used. Old hose-sets 

should not be reused.

n

  Only authorised spare parts shall be used  

in the event of failure.

SAVE THESE INSTRUCTIONS

n

  Keep area around the exhaust opening  

and adjacent surrounding areas free from  

the accumulation of lint, dust, and dirt. 

n

  Ventilation openings in the base shall not  

be obstructed by a carpet or similar object.

n

  The fresh air ventilation openings into the 

room and into the dryer must not be blocked 

or sealed.

n

  Emergency stop control: After installation, 

access to mains plug or disconnection from 

mains supply via a double-pole switch must 

be ensured at all times in order to ensure 

immediate deactivation of the dryer in case 

of emergency.

n

  The interior of the dryer and dryer exhaust 

vent should be cleaned periodically by 

qualified service personnel.

STACKED WASHER/DRYER SAFETY

Summary of Contents for MLG22PD

































Reviews: