MAYSER 1006747 Operating Instructions Manual Download Page 2

121022 v1.02-RiA 

Operating instructions SG-RS 309-2 

Page 2/23

 

Copyright

The reproduction, distribution and utilisation of this document as well as the communication of its contents 
without express authorisation is prohibited. Offenders will be held liable for the payment of damages. All 
rights reserved in the event of the grant of a patent, utility model or design.
© Mayser Ulm 2022

Safety first!

 

Read the instructions carefully before use.

 

The warnings in the instructions are there to warn you of any unex-
pected dangers. Always heed the warnings.

 

Keep the instructions somewhere safe so you can refer to them 
throughout the product’s entire service life.

 

Pass the instructions on to every subsequent owner or user of the 
product.

 

Add any supplement received from the manufacturer to the instruc-
tions.

 

Observe the information under “Safety” (starting on 
page 5).

Conformity

The Declaration of Conformity is available in the Downloads section of our web-
site: www.mayser.com.

The design type of the product complies with the basic requirements of the  
following directives:

 

2006/42/EC  (Safety of Machinery)

 

2011/65/EU (RoHS)

 

2014/30/EU (EMC)

EC type examination

The product was tested by an independent institute.
There is an EC type examination certificate to confirm conformity.
The EC type examination certificate is stored in the Downloads section of our 
website: www.mayser.com.

The Declaration of Conformity is available in the Downloads section of our web-
site: www.mayser.com.

The design type of the product complies with the basic requirements of the fol-
lowing UK Statutory Instruments:

 

2008 No. 1597  (Machinery)

 

2012 No. 3032  (RoHS)

 

2016 No. 1091  (EMC)

Summary of Contents for 1006747
























Reviews: