Maxx 20569, User Manual

Page: 126 / 134

126
8. UNDERHÅLL AV SÅGKEDJA OCH STÅNG
Skär standardstandarder:
Innan fyllning:
• Se till att sågkedjan är ordentligt fastsatt.
• Se till att motorn är avstängd.
• Använd en rund fil med rätt storlek för kedjan.
Modell 20569
Pitch (in.(mm)) 120” (1.27mm)
Oljetank
Ta bort oljefiltret med en trådkrok genom
påfyllningshålet och rengör det i bensin. När
du sätter tillbaka filtret i tanken, se till att det
finns i det nedre högra hörnet. Ta också bort
skräp i tanken.
Tändstift
Rengör elektroderna med en borste och
återställ gapet till 0,65 mm om det behövs.
Zaagketting
Det är mycket viktigt för smidig och
säker drift att alltid hålla kniven vassa.
Kniven måste slipas när:
• Sågspån blir pulverformig.
• Du behöver extra kraft för att klippa.
• Klippbanan går inte rakt
• Vibrationer ökar.
• Bränsleförbrukningen ökar
Zorg ervoor dat u veiligheidshand-
schoenen draagt.
Redskap
Kontrollera att det inte finns sprickor och för
mycket slitage som stör kedjedriften. Om slita-
ge är betydande, byt ut den mot en ny. Instal-
lera aldrig en ny kedja på ett slitet kedjehjul
eller en sliten kedja på ett nytt kedjehjul.
3. Oil tank
With a wire hook, take out the oil filter through the
filler port and clean in gasoline. When putting the
filter back into the tank, make sure that it comes
to the front right corner. Also clean off dirt in the
tank.
4. Spark plug
Clean the electrodes with a wire brush and reset
the gap to 0.65 mm as necessary.
5. Sprocket
Check for cracks and for excessive wear
interfering with the chain drive. If the wear is
considerable, replace it with new one. Never fit a
new chain on a worn sprocket, or a worn chain on
a new sprocket.
8. Maintenance of Saw Chain and Guide Bar

Saw Chain
Place the file on the cutter and push straight
forward.
Keep the file position as illustrated.
Cutter setting standards:
Before filling:
⚫
Make sure the saw chain is held securely.
⚫
Make sure the engine is stopped.
⚫
Use a round file of proper size for the chain .
Model 20569
Pitch (in.(mm)) 1/20 ” (1.27mm)
After each cutter has been filed, check the depth
gauge and file it to the proper level as illustrated.
Be sure to wear safety gloves.
It is very important for smooth and safe
operation to always keep the cutters
sharp.
The cutters need to be sharpened when:
⚫
Sawdust becomes powder-like.
⚫
You need extra force to saw in.
⚫
The cut path does not go straight.
⚫
Vibration increases.
⚫
Fuel consumption increases.
3. Oil tank
With a wire hook, take out the oil filter through the
filler port and clean in gasoline. When putting the
filter back into the tank, make sure that it comes
to the front right corner. Also clean off dirt in the
tank.
4. Spark plug
Clean the electrodes with a wire brush and reset
the gap to 0.65 mm as necessary.
5. Sprocket
Check for cracks and for excessive wear
interfering with the chain drive. If the wear is
considerable, replace it with new one. Never fit a
new chain on a worn sprocket, or a worn chain on
a new sprocket.
8. Maintenance of Saw Chain and Guide Bar

Saw Chain
Place the file on the cutter and push straight
forward.
Keep the file position as illustrated.
Cutter setting standards:
Before filling:
⚫
Make sure the saw chain is held securely.
⚫
Make sure the engine is stopped.
⚫
Use a round file of proper size for the chain .
Model 20569
Pitch (in.(mm)) 1/20 ” (1.27mm)
After each cutter has been filed, check the depth
gauge and file it to the proper level as illustrated.
Be sure to wear safety gloves.
It is very important for smooth and safe
operation to always keep the cutters
sharp.
The cutters need to be sharpened when:
⚫
Sawdust becomes powder-like.
⚫
You need extra force to saw in.
⚫
The cut path does not go straight.
⚫
Vibration increases.
⚫
Fuel consumption increases.
3. Oil tank
With a wire hook, take out the oil filter through the
filler port and clean in gasoline. When putting the
filter back into the tank, make sure that it comes
to the front right corner. Also clean off dirt in the
tank.
4. Spark plug
Clean the electrodes with a wire brush and reset
the gap to 0.65 mm as necessary.
5. Sprocket
Check for cracks and for excessive wear
interfering with the chain drive. If the wear is
considerable, replace it with new one. Never fit a
new chain on a worn sprocket, or a worn chain on
a new sprocket.
8. Maintenance of Saw Chain and Guide Bar

Saw Chain
Place the file on the cutter and push straight
forward.
Keep the file position as illustrated.
Cutter setting standards:
Before filling:
⚫
Make sure the saw chain is held securely.
⚫
Make sure the engine is stopped.
⚫
Use a round file of proper size for the chain .
Model 20569
Pitch (in.(mm)) 1/20 ” (1.27mm)
After each cutter has been filed, check the depth
gauge and file it to the proper level as illustrated.
Be sure to wear safety gloves.
It is very important for smooth and safe
operation to always keep the cutters
sharp.
The cutters need to be sharpened when:
⚫
Sawdust becomes powder-like.
⚫
You need extra force to saw in.
⚫
The cut path does not go straight.
⚫
Vibration increases.
⚫
Fuel consumption increases.
3. Oil tank
With a wire hook, take out the oil filter through the
filler port and clean in gasoline. When putting the
filter back into the tank, make sure that it comes
to the front right corner. Also clean off dirt in the
tank.
4. Spark plug
Clean the electrodes with a wire brush and reset
the gap to 0.65 mm as necessary.
5. Sprocket
Check for cracks and for excessive wear
interfering with the chain drive. If the wear is
considerable, replace it with new one. Never fit a
new chain on a worn sprocket, or a worn chain on
a new sprocket.
8. Maintenance of Saw Chain and Guide Bar

Saw Chain
Place the file on the cutter and push straight
forward.
Keep the file position as illustrated.
Cutter setting standards:
Before filling:
⚫
Make sure the saw chain is held securely.
⚫
Make sure the engine is stopped.
⚫
Use a round file of proper size for the chain .
Model 20569
Pitch (in.(mm)) 1/20 ” (1.27mm)
After each cutter has been filed, check the depth
gauge and file it to the proper level as illustrated.
Be sure to wear safety gloves.
It is very important for smooth and safe
operation to always keep the cutters
sharp.
The cutters need to be sharpened when:
⚫
Sawdust becomes powder-like.
⚫
You need extra force to saw in.
⚫
The cut path does not go straight.
⚫
Vibration increases.
⚫
Fuel consumption increases.
3. Oil tank
With a wire hook, take out the oil filter through the
filler port and clean in gasoline. When putting the
filter back into the tank, make sure that it comes
to the front right corner. Also clean off dirt in the
tank.
4. Spark plug
Clean the electrodes with a wire brush and reset
the gap to 0.65 mm as necessary.
5. Sprocket
Check for cracks and for excessive wear
interfering with the chain drive. If the wear is
considerable, replace it with new one. Never fit a
new chain on a worn sprocket, or a worn chain on
a new sprocket.
8. Maintenance of Saw Chain and Guide Bar

Saw Chain
Place the file on the cutter and push straight
forward.
Keep the file position as illustrated.
Cutter setting standards:
Before filling:
⚫
Make sure the saw chain is held securely.
⚫
Make sure the engine is stopped.
⚫
Use a round file of proper size for the chain .
Model 20569
Pitch (in.(mm)) 1/20 ” (1.27mm)
After each cutter has been filed, check the depth
gauge and file it to the proper level as illustrated.
Be sure to wear safety gloves.
It is very important for smooth and safe
operation to always keep the cutters
sharp.
The cutters need to be sharpened when:
⚫
Sawdust becomes powder-like.
⚫
You need extra force to saw in.
⚫
The cut path does not go straight.
⚫
Vibration increases.
⚫
Fuel consumption increases.
Efter att varje blad har fyllts på, kontrollera
djupmätaren och arkivera det till rätt nivå enligt
bilden.