MaxPro PROFESSIONAL MPBMS255L, Manual

Page: 12 / 46

9
GB
-Lift the handle (1) and r elease the on / off s wi tch button (15).
-B e f o r e r emo v e the w ork piece ensu r e the handle (1 ) of the machine is a upper position and the saw blade
stand still.
13.Mitre-cuts ( rotary table 0 degree )
The c r osscut saw c an be used to make mit r e cuts of 0-45 in r elation to the w ork f ace.
- Adjust the be v el le v er handle (fig. 13)
- Loosen the be v el le v er handle (18)
- T urn the table (8) of the machine into the desi r ed position, the angle c an be r ead out f r om indi c ator ( 18a)
- After the adjusting tighten the be v el le v er handle (18)
-R elease the table lock button (7a) and tighten the table lock handle (7)
-Hold firmly the handle (1) and p r ess the on off s wi tch (15), the saw blade will start running and w ait till it
r each his maximal speed.
-Unlock the gua r d lock handle (2) and push slowly the handle (1) and keep p r essing till the w ork piece is cut
c ompletely (fig 15.)
-Lift the handle (1) and r elease the on / off s wi tch button (15).
-B e f o r e r emo v e the w ork piece ensu r e the handle (1 ) of the machine is a upper position and the saw blade
stand still.
14.Mitre-cuts ( rotary table 0 degree ) and rotary table 0-45 degree
The c r osscut saw c an be used to make mit r e cuts of 0-45 in r elation to the w ork f ace and at the same time
0-45 deg r ee in r elation to the stop r ail. ( double mit r e cut )
-S et the r ota r y table at desi r ed position (fig. 12 )
-Loosen the table lock handle (7)
-Pr ess and keep p r essed the table lock button (7a) and turn the turning table to the desi r ed position
-R elease the table lock button (7a) and tighten the table lock handle (7)
-Adjust the be v el le v er handle (fig. 13)
-Loosen the be v el le v er handle (18)
-T urn the table (8) of the machine into the desi r ed position, the angle c an be r ead out f r om indi c ator ( 18a)
-After the adjusting tighten the be v el le v er handle (18)
-Hold firmly the handle (1) and p r ess the on off s wi tch (15), the saw blade will start running and w ait till it
r each his maximal speed.
-Unlock the gua r d lock handle (2) and push slowly the handle (1) and keep p r essing till the w ork piece is cut
c ompletely (fig 15.)
-Lift the handle (1) and r elease the on / off s wi tch button (15).
-B e f o r e r emo v e the w ork piece ensu r e the handle (1 ) of the machine is a upper position and the saw blade
stand still.
15.Replacing the saw blade. ( Fig. 17 – 20 )
-B e f o r e changing the saw blade, r emo v e the po w er plug !
-W ear w ork glo v es to p r e v ent inju r y when changing the saw blade.
-Lift the handle (1) till it maximum position, guide the handle when it is lifting up w a r ds.
-Loosen the sc r ew (25a) on the c o v er plate (25)
-Pull back the adjustable blade gua r d (7) and at the same time guide the c o v er plate (25) at the upper
di r ection to achie v e access to the flange bolt.
-Pr ess the saw shaft lock (23) with one hand in o r der to lock the saw blade, at the same time position the
Allen key (27) on the flange bolt (26)
-Loosen with some f o r ce the flange bolt (26) with the Allen key (27 ) at clockwise di r ection.
-T urn the flange bolt (26) right out and r emo v e the flange (28), while r emo v e the flange (28) hold the saw
blade (3) in your hand.
-T ake the saw blade (3) off the inner flange and pull it out down w a r ds.
-Ca r eful clean the flanges and the flange bolt (26)