background image

 

Safety Information

 

 

 

WARNING 

 

 

Ø

 

DO NOT 

hold the radio in such a manner that the antenna is next to, or touching, exposed parts 

of the body while transmitting. 

 

Ø

 

DO NOT 

allow children to operate transmitter-equipped radio equipment. 

 

 

 

CAUTION 

 

Ø

 

DO   NOT  

operate  the  radio  near  unshielded  electrical  blasting  caps  or  in  an  explosive 

atmosphere unless it is a type especially designed and qualified for such use. 

 

Ø

 

NEVER 

use the radio in an aircraft. 

 

Ø

 

NEVER 

use the radio near to sensitive medical equipment or in areas where instructed not to do 

so, e.g. Petrol filling stations. 

 

Ø

 

When used in a vehicle, do not mount the radio unit on or near the Airbag or Airbag activation 

device. 

 

Ø

 

The  use  of  an  accessory  not  recommended  or  supplied  by  Maxon  may  cause  damage  to 

equipment or injury to personnel, and will invalidate warranty. 

 

Ø

 

The outlet must not be obstructed and must be easily accessible at all times. 

 

Ø

 

Never 

attempt to disassemble, modify or repair the unit unless the work is carried out by an 

 

approved Dealer. 

 

Incorrect assembly, modification or repair may cause irreparable damage to your unit and will 

invalidate warranty. 

For service or repair always return your radio to an authorized Dealer. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for SD-17OEX Series























Reviews: