background image

5

4

model no. 058-9367-8 |  contact us 1-888-670-6682

NOTE:

 

The word “Note” is used to inform the reader of 

something he/she needs to know about the tool.

COLLET

SPEED (NO LOAD)

WORKING PRESSURE

CFM REQUIREMENT

AIR INLET

WEIGHT

AIR HOSE REQUIED

1/4" (6.4 mm)

20,000 RPM

90 PSI

2.2  @ 90 PSI

1/4"-18 NPT

1 lb 3 oz (0.53 kg)

3/8” (9.5mm)

CFM: Cubic Feet per Minute (the volumetric flow rate of air corrected to 

         standardized conditions of temperature and pressure).
NPT: National Pipe Thread.

TECHNICAL SPECIFICATIONS

This manual contains information that relates to PROTECTING PERSONAL 
SAFETY and PREVENTING EQUIPMENT PROBLEMS. It is very important 
to read this manual carefully and understand it thoroughly before using 
the product. The symbols listed below are used to indicate this 
information.

These precautions are intended for the personal safety of the user and 
others working with the user.
Please take time to read and understand them.

DANGER!

WARNING!

CAUTION!

PERSONAL SAFETY

Potential hazard that will result in serious
injury or loss of life.

Potential hazard that could result in
serious injury or loss of life.

Potential hazard that may result in
moderate injury or damage to equipment.

TM

Summary of Contents for 058-9367-8














Reviews: