Maxcess MAGPOWR TLC-B Load Cell User Manual Download Page 24

Page: 24 / 24

8-1

SERVICE

Service requests and
replacement parts

To request service or to get replacement parts, contact one of
the following addresses:

Fife Corporation
222 West Memorial Rd.

Oklahoma City, OK, 73114,  USA
Phone:  1.405.755.1600
Fax: 1.405.755.8425
Web:  www.maxcessintl.com

Fife-Tidland GmbH

Max-Planck-Strasse 8
65779 Kelkheim

Deutschland
Telefon: +49.6195.7002.0
Fax:  +49.6195.7002.933
Web:  www.maxcess.eu

Siemensstrasse 13-15
48683 Ahaus
Deutschland

AMERICAS

Tel +1.405.755.1600

Fax +1.405.755.8425

[email protected]

www.maxcessintl.com

EUROPE, MIDDLE EAST

AND AFRICA

Tel +49.6195.7002.0

Fax +49.6195.7002.933

[email protected]

www.maxcess.eu

CHINA

Tel +86.756.881.9398

Fax +86.756.881.9393

[email protected]

www.maxcessintl.com.cn

INDIA

Tel +91.22.27602633

Fax +91.22.27602634

[email protected]

www.maxcess.in

JAPAN

Tel +81.43.421.1622

Fax +81.43.421.2895

[email protected]

www.maxcess.jp

KOREA, TAIWAN,

AND SE ASIA

[email protected]

www.maxcess.asia

Summary of Contents for MAGPOWR TLC-B Load Cell

























Search results

Summary of Contents for MAGPOWR TLC-B Load Cell

Reviews:

Brands by name

Popular brands

Maxcess MAGPOWR TLC-B Load Cell, User Manual

Search results

Summary of Contents for MAGPOWR TLC-B Load Cell

Reviews:

Brands by name

Popular brands