Rev.
Descrizione
Redatto/Gestito
Approvato
Cod.Ident.
Pagine
Data Em.
0.6
Manuale Istruzioni
GN
UTEC
B041.M01.EN
8
/47
07/2014
HARDWARE:
The main hardware features of the machine’s mother
board are described as follows.
ATTENTION
Even if designed and potentially available, some features
could be not be present on the control unit box.
•
312 MHz processor that can be expanded up to 806 MHz.
•
64 MB RAM that can be expanded up to 128 MB.
•
32 MB flash memory that can be expanded up to 256 MB.
•
LCD TFT QVGA (320x240 pixel) touch-screen.
•
Keyboard with 5 crosswise keys.
•
One audio channel.
•
Buzzer.
•
Clock.
•
8 digital outputs.
•
8 digital inputs.
•
1 analog output (16 bit - 65536 points).
•
8 analog inputs (two of them at high performances).
•
Ethernet 100 Mbit for PC connection.
•
2 USB-Host (to connect mouse/keyboard/pen drive).
•
1 USB-Client.
•
Slot SD-Card.
•
1 RS232.
•
1 RS485.
•
2 controllers for step motors.
•
Expansion slot for additional analog inputs.
•
Expansion slot for motors control.
MAIN FEATURES:
•
Gyratory angle: adjustable from 0 to 2,4°
•
Gyration rate: adjustable from 5 to 60 work cycles/min
•
Compacted specimen size: dia 100 and 150 mm; height
from 0 to 200 mm for both sizes.
•
Vertical load on 150mm dia specimen: adjustable from 10 to
900 kPa
•
Vertical load on 100 mm dia specimen: adjustable from 23
to 1500 kPa
SOFTWARE:
The main software features of the machine’s mother board
are listed as follows
•
Operating system: “Windows Embedded CE 6.0 R2”.
•
More intuitive interface and a simplified management of
the machine (start up of the test with few and simple
commands).
•
More
opportunities
for
calculations
and
graphic
visualization (graphs on the machine and printing of the
results in a graphic mode).
•
More opportunities for languages and International format
management (date and time, decimal separator, unit of
measurement…).
•
Modular structure of the software in order to allow the
installation of new test modules later.
•
The software on the machine can be easily updated.
•
An unlimited memory provided by the SD-Card and USB-
Host slots.
Possibility to connect the machine to Internet in order to
activate the remote checking functions.
2.02
DIMENSION AND WEIGHT
A
LENGTH
640 mm
B
WIDTH
500 mm
H
HEIGHT
1060mm
WEIGHT
250Kg
2.03
ELECTRICAL SUPPLY
On
the
identification
nameplate of the machine
are
reported
the
identification data and the
electrical characteristics.
Power supply:
230V
1ph
50/60Hz
1000W
Picture
. 5
2.04
NOISE
The air noise emission levels shown do not necessarily imply the levels of exposure to the worker.
The levels of exposure to the operator are obviously linked to the emission levels of the appliance; however other factors
influence the levels of exposure to the operator: length of exposure, environmental characteristics, the presence of other
machines etc. The appliance emission levels allow anyway an estimate to be carried out on the dangers due to noise.
If the daily personal exposure is equal to or more than 85 dB (A) it is advisable to use the Individual Protection Devices
(protective headphones, plugs, etc.). If the daily personal exposure is equal to or more than 90 dB (A) it is compulsory to use
Individual Protection Devices (protective headphones, plugs, etc.). For further information consult the standards in force in the
country of installation.
