MCL1214IW, -G, -O, -Y
3
rev. 01/24/20
MCL1214IW, -G, -O, -Y 12V 1/4" Impact Wrench
Service
• Tool service must be performed only by the MATCO
authorized service centers listed. Service or maintenance
performed by unqualified personnel may result in a risk of
injury. Repair by unqualified personnel, use of unauthorized
parts, and failure to follow maintenance instructions may
create a risk of shock or injury.
SAVE THESE INSTRUCTIONS!
SPECIFIC SAFETY RULES
DO NOT let comfort or familiarity with product replace strict
adherence to cordless product safety rules. If you use this
tool unsafely or incorrectly, you can suffer serious personal
injury.
• Hold tool by insulated gripping surfaces when performing an
operation where the accessories may contact hidden wiring.
Contact with a “live” wire will also make exposed metal parts of
the tool “live” and shock the operator.
• Be aware that this tool is always in operating condition, because it
does not have to be plugged into an electrical outlet.
• Always be sure you have firm footing.
• Be sure no one is below when using the tool in high locations.
• Hold the tool firmly and use both hands.
• Keep hands and hair away from rotating parts.
• Do not leave the tool running. Do not force tool to stay in the “on”
position. Operate the tool only when hand-held.
• Do not touch the impact socket or the workpiece immediately after
operation; they may be extremely hot and could burn your skin.
• Some material contains chemicals which may be toxic. Take
caution to prevent working dust inhalation and skin contact.
Follow material supplier safety data.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
OPERATING INSTRUCTION
Installing Or Removing Battery Pack
(See Fig.1, Fig.2)
1. Your new battery pack is not fully charged. You may
need to charge it before use.
2. Make sure the switch is in the "off" position before
insertion/removal of a battery pack.
3. To remove a battery pack, depress both tabs on
either side of the battery and pull downward.
4. To insert a battery pack, align the battery with the
tool housing and push battery inward until click
indicating battery is fully installed.
Charging The Battery Pack
(See Fig.3)
1. Battery may not charge when it is above a certain
preset temperature limit. Allow temperature of
battery to cool before charging.
2. The charge process will take less than one hour.
3. After charging, unplug the charger from the power source and
stow away in a safe place.
Tool Operation:
• Always be sure that the tool is switched off and the
battery cartridge is removed before installing or removing
the impact socket.
1. To install the impact socket, push the impact socket onto the
anvil as far as it will go.
2. To remove the impact socket, simply pull the impact socket
from the anvil.
3. To start the tool, simply pull the trigger. Release the trigger to
stop.
4. For reversing the tool, use the forward/reverse switch on the
drive unit. The directions of the rotation are also shown on the
face of the switch.
5. Always check the direction of rotation before operation..
6. Use the forward/reverse switch only after the tool comes to a
complete stop. Changing the direction of rotation before the
tool stops may damage the gears.
7. Hold the tool firmly in place, make sure the impact socket is
completely over the nut or bolt. Apply forward pressure to the
tool to the extent that the impact socket will not slip off the nut
or bolt. Pull the trigger to begin.
NOTE:
• Use the proper impact socket size for the nut that you intend to
install or remove.
• Hold the tool pointed straight at the nut. If you tighten the nut
for a time longer than it needs, the nut or point of the driver
socket may be overstressed, stripped, damaged, etc. When
tightening a standard nut in a steel plate, the proper tightening
torque can be obtained in an extremely short time (approx.
0.1-0.2 seconds).
• Turn the tool off as soon as the impact sound is heard.
• When tightening nut M6 or smaller, carefully adjust pressure on
the switch trigger so that the nut is not damaged.
8. The tightening torque is affected by a wide variety of factors
including the following.
• When the battery cartridge is discharged almost completely,
voltage will drop and the tightening torque will be reduced.
• Driving a bolt: Even though the torque coefficient and the class
of bolt are the same, the proper tightening torque will differ
according to the diameter of the bolt.
9. Even if the diameter of the bolts are the same, the proper
tightening torque will differ according to the torque coefficient,
the class of the bolt and the bolt length.
10. The manner in which the tool is held or the driving position
of the material to be tightened will affect the torque.
Make sure that the impact wrench is turned off and the
battery cartridge is removed before carrying out any
work on the tool. To maintain product safety and
reliability, repairs, maintenance or adjustments should be
carried out by a Matco authorized service center.
Fig. 1
Fig. 2
Fig. 3
