EN
EN
13
14
3. Place the appropriate accessory in the unit for your selected cooking feature and close the cover.
To start preheating press START / STOP. While the device is preheating, insert the probe in the
middle of the thickest part of the largest piece of protein, close (but not touching) the bone. DO NOT
insert the probe either vertically or at an angle, as it does not provide accurate reading.
4. When the device has preheated and the "Add Food" flashes on the screen, open the cover, put
food inside the device and close the cover over the cord of the probe. The monitor will now show the
reading of the temp probe as it cooks the food.
4. Press START/STOP to begin preheating. PRE will appear on the display screen, and the progress
bar will begin. It can take approximately 4 minutes.
5. Display will show 'Add food' when preheating is completed.
6. Open the cover and put the ingredients on the grill. When the cover is closed, cooking begins and
the timer counts down.
NOTE: If you just want to use the temp probe for testing your food’s temperature press TEMP ACE
button for 2 seconds and the internal temperature of the food will appear on the screen for 5
seconds. When the screen starts flashing, you weren't holding the button long enough. Refer to the
page about Troubleshooting.
7. The device will beep when cook time is through, and END appears on the display screen. Push
TIME up arrow and push START / STOP if you need to add more time to cook the food. When using
the detector the time change varies. Page 9, phase 6b of reference, when using the probe
.
8. Keep the cover open after removing the food, so that the machine can cool down faster. After
cooking, the stainless steel cover on the outside of the unit will be hot.
NOTE: When Cooking same food in batch, refer to the instructions at the bottom of page 7.
5. When your food inside hits the temperature you set, the device will beep and the display shows
‘End’. Press TEMP ACE button for 2 sec, the display will go on showing the internal food temperature.
6a. Temp probe cooking complete:
Remove protein from the unit, insert the probe and position it on a plate for a minimum of 5 minutes
to rest. When it is cooking, the protein should carry over to rest. If it hits the temperature of carry-over
cook on the chart from previous page you're complete with the cooking.
6b. Cooking more food without the Temp probe:
If you use the same feature to cook more food but do not need to use the probe, simply press
START/STOP to restart. Then press the TIME arrow to set a new cook time. Change the temperature
of the function, if applicable. To get started click START / STOP. If you use a different function to cook
more food, pick that function before setting the new time and temperature for cook.
NOTE: You can test the food's internal temperature at any time, even if it does not run a cook
feature. Only click the Temp button for 2 seconds.
6c. Cooking same food in batch with the Temp probe:
If you are cooking same food (meat) in batch, remove the probe from the cooked protein and place it
in the center of the largest uncooked protein portion. Click the TEMP button, set the internal tempera-
ture you want and click START / STOP. "Add Food" will show, let the device run for about 3 minutes
until the cover is opened and add the next batch of protein. Then, take step 5.
TYPES OF COOKING
Make sure the machine is plugged in before turning it on then tap the power button.
GRILL
1. Place the cooking pot on the main unit with the indent on the pot corresponding to the rear bump.
Then through the grill with the handles facing up into the bowl. Make sure the splatter guard is in
place and close the cover.
2. Tap GRILL button. The default temperature level on the left side of the control panel will light, and
the corresponding air temperature will appear on the display screen. To change the temperature
setting, press the Grill button, or the up and down TEMP arrows.
3. Click the TIME arrows up and down to set the cook time, in approximately 1 minute, up to 30
minutes, or follow the instructions on page 8 to adjust the temperature of a probe using the TEMP
ACE button.
7. We highly recommend shaking ingredients regularly for better results. When the cover is removed
the machine pauses. To shake the tub, use silicone-tipped tongs, or oven mitts. When done, close
the cover. After cover is closed, cooking should automatically resume.
8. The device will beep when cook time is through, and END appears on the display screen. Remove
the food, and close the lid. Simply click the TIME up arrow and click START / STOP to add more time
to cook the food.
ROAST
1. Place the pot in the unit with the indent on the pot matched with the bump on the main unit and
close the hood.
2. Click the button to ROAST. It shows the default temperature setting. Using the TEMP arrows up
and down to adjust temperature.
NOTE: This product is very powerful. If you find regular recipe, please reduce 10°C when using
Smokeless Grill. Frequently test the food to prevent overcooking.
3. Using the TIME arrows up and down to set the cook time, in period of 1 to 90 minutes, or follow
the instructions on page 8 to adjust the temperature of a probe using the TEMP button.
4. To start preheating press START / STOP. PRE appears on the screen, and the progress bar
begins. Preheat will take about 4 minutes.
NOTE: For better performance, though preheating is highly recommended, you can skip it by
pressing the ROAST button once more. "Add Food" flash across the screen. Place ingredients in the
AIR CRISP
1. Place the cooking pot within the unit with the indent on the pot aligned with the main unit bump.
Place the cooking pot within the unit with the indent on the pot aligned with the main unit bump. Then
closet he lid.
2. Click the AIR CRISP button on the Window. It shows the default temperature environment. Using
the TEMP arrows up and down to set temperature.
3. Using the up and down TIME arrows to set the cook time, in approximately 1 to 90 minutes, or
follow the instructions on page 8 to adjust the temperature of the probe with the TEMP ACE button.
4. To start preheating press START / STOP. PRE appears on the screen, and the progress bar
begins. Preheat will take up to 3 minutes.
NOTE: Although preheating is highly recommended for better performance, you can skip it again by
pressing the AIR CRISP button. "Add Food" flash across the monitor. Place ingredients in the
cooking pot and open the lid. When the cover is closed, cooking begins and the timer counts down.
5. Display will show 'Add food' when preheating is completed.
6. Open the lid and place ingredients in the cooking pot. Once the hood is closed, cooking will begin
and the timer will start counting down.
NOTE: If you just want to use the temperature probe for testing your food, press TEMP button for 2
seconds and the internal temperature of the food will appear on the screen for 5 seconds. When the
screen starts flashing, you weren't holding the button long enough. Refer to Page on Troubleshooting.
cooking pot and open the cover. When the cover is closed, cooking begins and the timer counts
down.
5. Display will show 'Add food' when preheating is completed.
6. Open the cover and bring ingredients into the pot. When the cover is closed, cooking begins and
the timer counts down.
NOTE: If you just want to use the temp probe for testing your food, press TEMP ACE button for 2
seconds and the internal temperature of the food will appear on the screen for 5 seconds. When the
screen starts blinking, you weren't holding the button long enough. Refer to Page on Troubleshooting.
7. The device will beep when cook time is through, and END appears on the display screen. Remove
the food, and close the lid. Simply click the TIME up arrow and click START / STOP to add more time
to cook the food.
BAKE
1. Position the cooking pot on the main unit with the indent on the pot aligned with the mark, and
then close the cover.
2. Tap BAKE button. It shows the default temperature setting. Using the TEMP arrows up and down
to adjust temperature.
NOTE: Convert typical recipes to a temperature drop of 10 ° C. Very frequently test the food to
prevent overcooking.
3. By using the up and down TIME arrows to set the cook time, in periods of 1 to 90 minutes, or
follow the instructions on page 8 to adjust the temperature of the probe using TEMP ACE button.
4. To start preheating press START / STOP. PRE appears on the screen, and the progress bar
begins. Preheat will take up to 3 minutes.
NOTE: Although it is highly recommended to preheat for better performance, you can skip it again by
pressing the BAKE button. "Add Food" flash across the screen. Place ingredients in the cooking pot
and open the cover. When the cover is closed, cooking begins and the timer counts down.
5. Display will show 'Add food' when preheating is completed.
6. Open the cover and add ingredients to the pot, or directly place your bake pan in the bottom of the
pot, and close the cover to start cooking. When the cover is closed, cooking begins and the timer
counts down.
NOTE: If you just want to test your food using the temp probe, press TEMP ACE button for 2
seconds and the internal temp of the food will show on the screen for 5 seconds. When the screen
starts flashing, you weren't holding the button long enough. Refer to Page on Troubleshooting.
7. The device will beep when cook time is over, and END appears on the display screen. Simply click
the TIME up arrow and click START / STOP to add more time to cook the food.
DEHYDRATE
NOTE: TEMP ACE button and temp probe is not applicable for use in this function.
1. Place the cooking pot in the unit with the mark on the pot matched with the mark on the main unit,
then add to the bottom of the pot a single layer of ingredients. Close the cover.
2. Click on DEHYDRATE click. It shows the default temperature setting. Using the TEMP arrows up
and down to set the temperature you want.
3. Using the TIME arrows to set the time of dehydration in in 1 minutes time up to 9 hours intervals.
4. To get started click START / STOP. In Dehydrate mode the device doesn't preheat.
NOTE: You should open the cover during dehydration to check on your meal. When the cover is
opened, the timer will pause, and then restart automatically after it is closed.
5. The device will beep when the dehydration time is complete, and END appears on the display
screen. Remove the food, and close the lid.
