manualshive.com logo in svg

MasterCraft 062-3408-6, Instruction Manual, Page: 16 / 20

Share
Download
MasterCraft 062-3408-6 Instruction Manual Download Page 16

headline bars

continuation tabs

notes

warnings

headline bars

continuation tabs

notes

warnings

model no. 062-3408-6 | contact us 1-800-689-9928

16

ASSEMBL

Y

 

INSTRUCTIONS

OPERA

TING INSTRUCTIONS

• 

Unscrew the priming plug.

• 

Fill water through priming hole as the 
picture shows to overflowing.

• 

Tighten the priming plug.

• 

To operate, plug the pump into a 115 V GFCI 
outlet.

• 

When the water level has been reduced to 
approximately 1/16" (1.6 mm) you MUST 
UNPLUG THE PUMP. DO NOT RUN DRY.

NON-SUBMERSIBLE TRANSFER PUMP INSTALLATION

NOTE:

• Always ensure the washer in the hose bib is not damaged. An airtight seal is necessary for this pump to operate.

• Make sure the end of the outlet hose is not under water. If the outlet is under water, the pump may not work. 

• Do not coil or kink the hose.

• If water is not pumping in 30 seconds, unplug the power cord and check the connection on the two ends of the 

   inlet hose to make sure there are no air leaks. Then, add water into the priming port again and repeat the process.

OPERATION

• 

Open the bottom cover.

• 

Thread the other end of the suction hose to 
the inlet of the pump.

• 

Thread a garden hose with a 3/4" (19 mm) 
NH fitting, a diameter of at least 5/8" (16 
mm), and a maximum length of  50' (15.2 
m), sold separately,  onto the discharge 
outlet of the pump.

NO KINKS!

NO COILS!

Suction

hose

Priming plug

Outlet

Suction

strainer

3/4" (19 mm) NH thread

Suction hose

Priming plug

Outlet

Suction 

strainer

Summary of Contents for 062-3408-6





















Reviews:

No comments