manualshive.com logo in svg

MasterCraft 062-3408-6, Instruction Manual, Page: 13 / 20

Share
Download
MasterCraft 062-3408-6 Instruction Manual Download Page 13

headline bars

continuation tabs

notes

warnings

13

•  Attach a garden hose with a 3/4" (19 mm) garden hose thread (not included) to the pump 

outlet.

•  Place the pump on a solid base in flooded area or any place that you would like to remove 

water. Plug the pump into a 115 V GFCI power outlet.

ASSEMBL

Y INSTRUCTIONS

SUBMERSIBLE UTILITY PUMP INSTALLATION

CAUTION!

•    Always use the handle to lift the pump. Never use the power cord to lift the pump. To avoid skin burns, unplug the 

pump and allow time for it to cool after periods of extended use.

WARNING

•    Always disconnect power source before attempting to install, service, or maintain the pump. Never handle a pump 

with wet hands or when standing on wet or damp surface or in water. Fatal electrical shock could occur.

•    Do not allow the plug to fall in water and do not stand in water while the pump is plugged in.

NOTE:

• The larger the inside diameter and the shorter the length of hose, the less pressure that is lost (or the larger the 

   flow rate).

• Be sure the 3/4" (19 mm) garden hose thread connector has a rubber gasket to minimize water leaks.

• Place upright on a solid base.

• The pump must be standing in at least 1 1/2" (38.1 mm) of water before you start it. The shaft seal is water 

   lubricated and may be damaged if the pump runs dry.

3/4" (19 mm) NH

thread

1 1/2” (38.1 mm)

Summary of Contents for 062-3408-6





















Reviews:

No comments