MasterCraft 060-1349-2 Instruction Manual Download Page 16

Page: 16 / 24

headline bars

continuation tabs

notes

warnings

model no. 060-1349-2 | contact us 1-800-689-9928

ADJUSTING THE CUTTING LINE LENGTH

(fig 10)

The trimmer head allows the operator to release
more cutting line without stopping the motor. As
line becomes frayed or worn, additional line can be
released by lightly tapping the bump knob on the
ground while operating the trimmer.

For best results, tap the bump knob on bare ground
or hard soil. If line release is attempted in tall grass,
the motor may overheat.

Always keep the trimming line fully extended. Line
release becomes more difficult as the cutting line
becomes shorter.

OPERA

TING INSTRUCTIONS

fig 10

Line cutting
blade

Bump knob

WARNING!

• Do not remove or alter the line cutting blade assembly. Excessive line length will cause the motor to overheat and may result

in serious personal injury.

FPO

Summary of Contents for 060-1349-2

























Search results

Summary of Contents for 060-1349-2

Reviews:

Related manuals for 060-1349-2

Brands by name

Popular brands

MasterCraft 060-1349-2, Instruction Manual

Search results

Summary of Contents for 060-1349-2

Reviews:

Related manuals for 060-1349-2

Brands by name

Popular brands