MasterCraft 058-1294-8 Instruction Manual Download

Page: 4 / 12

model no. 058-1294-8 | contact us 1-800-689-9928

PACKAGE CONTENTS

ASSEMBLY PREPARATION

1 Remove cartons, bags or foam containing the welder and accessories.

2 Check the contents with the packing list below.

2.2 Install the axle tube/bracket for the axles and wheels on the axle as shown in Fig. 2.1.

Stand the machine up and install the axle tube/bracket onto the back of panel using the screws and

washers provided. (You may want to prop the welder with wooden blocks for this step.)

ITEM

No.

QTY.

ARC welder

1 unit

Handle

1 pc
1 pc

Wheel kit (axle, wheels , axle holder etc)
Support

1 pc

Fastener pack

1 pair

Operator s manual

1 pc

1
2
3
4
5
6

PACKAGE CONTENTS

ASSEMBLY

1. Tools required for assembly: 8 and 10 mm open-end wrenches .

2.2.1 Lay the machine side panel on a flat surface. Install the metal bracket support on the bottom
using two sets of screws and washers from the hardware bag. See following image.

model no. 058-1294-8 | contact us 1-800-689-9928

Summary of Contents for 058-1294-8













Search results

Summary of Contents for 058-1294-8

Reviews:

Related manuals for 058-1294-8

Brands by name

Popular brands

MasterCraft 058-1294-8, Instruction Manual

Search results

Summary of Contents for 058-1294-8

Reviews:

Related manuals for 058-1294-8

Brands by name

Popular brands