DOUBLE SYSTEM
This sheet contains important information about how to use and the safety of the system. Observe the instructions and keep them for future reference.
Use the module ONLY with motors supplied. If it becomes necessary to replace one or both motors, contact your dealer.
1. TECHNICAL SPECIFICATIONS (@ 20°C)
- Power supply:
230 Vac, 50/60 Hz
- Contact capacity:
10A at 250 Vac
- Operating temperature:
from –20 to +55 °C
- Operating time:
130 sec
- Frequency:
433.42 MHz
- Memorizable transmitters:
15 (radio sensor included)
- Range (estimes):
100m outdoor, 20m indoor
2. NOTES ON RADIO SYSTEMS
- Radio installation cannot be used where there is a high disturbing factor (for examples: near police stations, airports, banks and hospitals). However it is advisable that a
technician could see the place before installing any kind of radio system in order to verify the possibility of a radio installation.
- Radio devices can be used only if any possible interference or malfunction of the transmitter or of the receiver are not a factor of risk, or if the factor of risk is cancelled by
security system.
- The presence of radio devices working at the same frequency of transmission (for example alarms and earphones) could interfere with radio receiver of central unit cutting
down the capacity of the transmitter and restricting the full functionality of the system.
3. WARNINGS
GENERAL
SAFETY
INSTRUCTIONS
-
Incorrect installation can cause serious injuries.
-
Keep these instructions for future maintenance work and disposal of the product.
-
All the product installation, connection, programming and maintenance operations must be carried out only by a qualified and skilled technician, who must
comply with laws, provisions, local regulations and the instructions given in this manual.
-
The wiring must comply with current IEC standards.
-
Certain applications require hold-to-run operation and can exclude the use of radio controls or require particular safety devices.
-
To prevent potentially dangerous situations, check the operating condition of the roller shutter/awning regularly..
WARNINGS
FOR
THE
INSTALLATION
-
Check that the package is intact and has not been damaged in transit.
-
Install the product carefully, using suitable tools.
-
Do not modify or replace parts without the manufacturer's permission. Do not pierce or tamper the box.
-
The power cord must be positioned so as not to come into contact with moving parts.
-
If there are several radio appliances in the same system, they must not be less than 1.5 m apart.
-
Do not install the product near metal surfaces.
-
Use momentary (hold-to-run) control buttons. Do NOT use stay-put switches.
-
Position the buttons within sight of the roller shutter/awning but a long way from its moving parts. Position the buttons more than 1.5 m from the floor.
-
The antenna cable carries line voltage. Do not cut the antenna cable as this would be dangerous. If the antenna cable is damaged, replace the product.
-
Adjust the mechanical limit switches of the motors before connecting them to the module.
WARNING
FOR
USE
-
The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they are supervised or given instructions on how to use the product by a person responsible for their safety.
-
Before operating the roller shutter/awning, make sure there are no people or objects in the area involved in its movement. Check the automation during
movement and keep people at a safe distance, until the movement ends.
-
Do not allow children to play with the appliance or with the fixed control devices. Also, keep the portable control devices (remote controls) out of the reach of
children.
-
Do not operate the roller shutter/awning when maintenance operations are being carried out (e.g. window cleaning). If the control device is automatic, disconnect
the motor from the power line.
4. ELECTRICAL CONNECTIONS
WARNINGS
- Make the connections with the power switched off.
- Check that the power line does not come from electrical circuits intended for lighting.
- A circuit breaker or residual current device must be inserted in the power line. An isolating device with overvoltage category III, namely distance between contacts
of at least 3.5 mm, must be inserted in the power line.
- Use momentary (hold-to-run) control buttons. Do NOT use stay-put switches.
- The control buttons are connected to the line voltage and must therefore be properly isolated and protected.
R
Rev. 02 del 07/04/2017
433,42 MHz
