Master Therm AirMaster aku Installation And Operating Manual Download Page 3

Page: 3 / 64

AM, EM, AQ, BA, ASW - IOM

page: 3/64

Ing.Ji

í Jiránek

4.8

Hydraulic system schematic....................................................................................................33

4.9

Piping Connection !!! use 2 spanners !!! ..........................................................................34

4.10

Pressure and Leak Test ..........................................................................................................34

4.11

Heat Insulation ........................................................................................................................34

4.12

Anti-Freeze Mixture.................................................................................................................35

4.13

Filling and Venting the Ground Loop .......................................................................................35

Connestion to the Heating System..................................................................................................36

5.1

Heating System – WARNING..................................................................................................36

5.2

Water Quality -Hardness dH and pH value..............................................................................36

5.2.1

Corrosion Inhibitors .........................................................................................................36

5.2.2

Bacterial and mould protection ........................................................................................36

5.3

Connection of Heat Pumps “AKU” – AM..................................................................................37

5.4

Connection of AQ Heat Pumps ...............................................................................................38

5.4.1

AQ Single-circuit Heating System....................................................................................38

5.4.2

AQ Multi-circuit Heating System – Switchable Heating of DHW.......................................39

5.4.3

AQ Multi-circuit Heating System – DHW Heating Using Charge Pump............................40

5.4.4

AQxxIC (combi) units recommended connection .............................................................41

5.5

Connection of AM MINI, EM Heat Pumps ...............................................................................42

5.5.1

Heating System with Pump Circuits and Through-flow Pre-heating of DHW....................42

5.5.2

AM MINI, EM Single-circuit Heating System....................................................................43

5.5.3

AM MINI, EM Multi-circuit Heating System - Switchable Heating of DHW........................44

5.5.4

AM MINI / EM Multi-circuit Heating System - DHW Heating Using Charge Pump............45

5.6

BoxAir and BoxAir Inverter system connection........................................................................46

5.6.1

Single loop heating system..............................................................................................46

5.6.2

BoxAir and BoxAir Inverter multi-circuit system with DHW...............................................47

5.6.3

BoxAir / BoxAir Inverter multi-circuits, charging pump DHW ............................................48

5.6.4

Heating system charge for BoxAir and BoxAir Inverter ....................................................48

5.6.5

Venting the system for BoxAir a BoxAir Inverter ..............................................................48

5.7

ASW units connection .............................................................................................................49

5.8

Heating Circuits.......................................................................................................................50

5.8.1

Manifolds.........................................................................................................................50

5.8.2

Pump heating circuits ......................................................................................................51

5.8.3

Mixing heating circuits .....................................................................................................51

5.9

Preparation of Domestic Hot Water (DHW) .............................................................................52

5.9.1

3 way valve tank in tank ..................................................................................................52

5.9.2

3 way valve with tank with heat exchanger (indirect, non-direct)......................................52

5.9.3

Charging pump for tank with heat exchanger ..................................................................53

5.9.4

Preheating in Accumulation Vessel of the Heating System and Electric Afterheating ......54

5.9.5

Safety / PT relief valve outlet ...........................................................................................54

5.10

Piping Connection !!! use 2 spanners !!! ..........................................................................55

5.11

Pressure and Leak Test ..........................................................................................................55

5.12

Heat insulation ........................................................................................................................55

5.13

General Instructions ................................................................................................................55

Electric Power Connection..............................................................................................................56

6.1

Hlavní napájení .......................................................................................................................56

6.2

Tariff signal, remote on/off signal ............................................................................................57

6.3

AM/EM indoor and outdoor unit electrical interconnection.......................................................57

6.3.1

EM60Z/EM75Z , 1OEM26-45VK, 1OEM60-75VK additional connection..........................57

6.4

External components (pumps, valves) ....................................................................................58

Control and measurement ..............................................................................................................58

7.1

Standard unit...........................................................................................................................58

7.2

Optional „Expansion Card“ ......................................................................................................58

7.3

Probes connection ..................................................................................................................58

7.4

Mixing valves servo.................................................................................................................59

7.5

Circulating pumps ...................................................................................................................59

7.6

pAD room terminals ................................................................................................................59

Summary of Contents for AirMaster aku

































































Search results

Summary of Contents for AirMaster aku

Reviews:

Related manuals for AirMaster aku

Brands by name

Popular brands

Master Therm AirMaster aku, Installation And Operating Manual

Search results

Summary of Contents for AirMaster aku

Reviews:

Related manuals for AirMaster aku

Brands by name

Popular brands