background image

 

11

Minimum 
Compressor 
On Time 

Con 

Minimum time that 

the compressor 
remain turned on  

Range: from 0 to 15 min  

2 min. 

Alarm Delay 

ALrd 

Time delay before 

the alarm goes off 
after the 
temperature fall 
off the two alarm 
set points 

Range: from 0 to 59 min  

30 – for LT 
45 
– for MT 

Compressor 
Run Time 

CPrn 

Time the 

compressor runs 
between defrosts 

 

12 – for MT 

Number of 
Defrosts 

nodF 

Number of defrosts 

per day 

from 0 to 8 (0 means 1 defrost 

every 48 hours)  

N/A – for LT 
– for MT 

Defrost Start 
Time 

dEF1-8 

Start time of each 

defrost 

 

N/A 

Defrost 
Duration 

dEFd 

Defrost duration 

time (back-up for 
defrost 
termination 
temperature) 

Range: from 0 min to 4 hours 

35 – for LT 
– for MT 

Fan Delay 

FAnd 

Delay time for the 

fan after defrost 
(back-up for fan 
cut-in 
temperature) 

Range: from 0 to 15 min  

– for LT 
– for MT 

Pump Down 

Pudn 

Pump down duration  Range: from 0 to 59 min  

0 min. 

Drip Time 

driP 

Drip time duration 

Range: from 0 to 59 min  

– for LT 
– for MT 

Setpoint 
Differential 

diF

°

 

Cut-in temperature 

differential  
Note: cut-in is cut-
out plus differential 

Range: from 1 to 25

°

  

10

°

 F–for LT 

7

o

– for MT 

Temperature 
Initiated 
Defrost 

tdEF 

Temperature that 

will initiate a 
defrost cycle 

Range: from – 40 to 40

°

F or – 40 to 

4

°

N/A 

Defrost 
Termination  
Temperature 

dEF

°

 

Temperature in the 

evaporator that 
will terminate the 
defrost cycle 

Range: from 0 to 75

°

F or –18 to 

25

°

C  

50

°

 F 

Fan Cut-In 
Temperature 

FAn

°

 

Temperature in the 

evaporator that 
will turn the fan 
on after defrost 

Range: from – 40 to 60

°

F or – 40 to 

23

°

30

°

 F–for LT 

60

o

F–for MT 

Low 
Temperature 
Alarm  

ALLo 

Low temperature 

setpoint that will 
make the alarm go 
off and the error 
message appear on 
the display 

Range: from – 40  to 83

°

F or – 40 to 

23

°

C  

-40

°

 F–for LT 

32

o

F–for MT 

Summary of Contents for TAF-27 ERC2 s



















Reviews: