background image

  Please  read  carefully  all  the  dimensions  and  recommendations  provided  in  the  technical 

specification  section  of  this  manual.    The  dimensions  given  comply  with  the  required  safety 
standard AS/NZS 2918:2001.  

  For  safety,  operational  and  warranty  compliance,  altering  the  appliance  in  any  way,  should  not  be 

attempted, No modifications are permissible.  

  Please  ensure  that  only  components  approved  by  Masport  heating  New  Zealand  are  used  on  the 

installation, as substitutes may adversely affect performance and might  nullify compliance with the 
requirements of AS/NZS 2918 safety standards. 

  The  Clutha  burner  was  tested  using  a  Masport  flue  system,  it  is  recommended  that  it  is  installed 

using  a  Masport  flue  system  or  a  flue  system  that  has  been  tested  and  complies  with  AS/NZS 
2918:2001  Appendix  F.  All  Masport  burners  have  been  tested  using  a  Masport  double  flue  shield 
and this must be used with your installation. 

  Masport recommends that the flue system  must be serviced annually by a NZHHA trained service 

agent. 

4.1 Cautions 

  This  appliance  is  not  intended  for  use  by  persons  (including  children)  with  reduced  physical, 

sensory,  or  mental  capabilities  or  lack  of  experience  and  knowledge  unless  they  have  been 
given  supervision  or  instruction  concerning  the  use  of  the  appliance  by  a  person  responsible 
for their safety. 

  Do not leave children unattended near  the alighted fire and keep them well away from the fire 

when in use. Supervise young children to ensure that they do not play with the appliance. 

  Do  not  use  flammable  liquids  or  aerosols  to  start  or  rekindle  the  fire.    Also,  do  not  use  such 

flammable materials near this appliance when operating. 

  Always keep clothing, firewood, furnishing, and other combustible materials at a safe distance 

from the fire. 

  Do not touch any part of the fire other than the door handle and the air control when in use, as 

all other parts can be extremely hot.   

  A  Cracked/broken  door  glass  makes  operation  of  the  heater  unsafe.    Do  not  operate  the  fire 

with a cracked/broken door glass. 

  Do not attempt to clean or maintain the fire when in use or with hot embers in  the combustion 

chamber.    Ensure  that  embers  and  all  other  parts  of  the  fire  have  cooled  down  completely 
before starting ash removal or other maintenance.  

  Do  not  use  the  fire  if  there  is  a  malfunction,  a  suspicion  of  breakage,  or  unusual  noises.  

Contact your Masport dealer or customer service team at Glen Dimplex, New Zealand. 

  This appliance should always be operated & maintained as per instructions in this manual. 

 

 
 
 

 
 
 
 
 
 
 
 
 
 
 

 

Failure to follow above warnings, cautionary measures 

and instruction given in this installation and operation 

manual will void the Masport Heating warranty of this 

product. 

Summary of Contents for CLUTHA


















Reviews: