Masimo SET Radical-7 Service Manual Download Page 23

Page: 23 / 40

Radical-7 Signal Extraction Pulse CO-Oximeter Service Manual

6-3

Symptom

Cause and Corrective Action
Steps
2. Replace Display

•

005

•

Dual UART Failed at Power Up

1. Replace Portable System Board

•

006

•

Oximeter Board Failure

1. Replace Oximeter Board

•

007

•

Oximeter MX Board

Communication Error

1. Verify Oximeter Board (SET)

Software is correct

a. If version is incorrect or not

displayed, return unit to an
authorized service center or use
a field upgrade tool to reload
the oximeter board software.

b. If version is correct, replace

Oximeter Board.

c. Replace Portable System Board

•

008

•

Real Time Clock Failure

1. Replace Portable System Board

•

009

•

Watchdog Failure

1. Replace Portable System Board

•

010

•

Docking Station Watchdog

Failure

1. Replace Docking Station System
Board.
2. Replace Portable System Board

•

200

•

Invalid SatShare coefficients

1. Replace Docking Station System
Board.

Symptom

Cause and Corrective Action
Steps

•

All Flashing LED's

1. Flashing alternates between
all LED's and AC Power
LED.
2. Refer to Radical-7

Operators

Manual for LED status
Parameters.

•

Communication error between

Portable and Docking Station

1. Verify software versions of
    Portable and Docking Station
    System Boards using the Portable
    menu
    a. If versions are incorrect or not

displayed, reload System
Application Software for that
device utilizing procedures
outlined in the Software

Summary of Contents for Radical-7









































Search results

Summary of Contents for Radical-7

Reviews:

Related manuals for Radical-7

Brands by name

Popular brands

Masimo SET Radical-7, Service Manual

Search results

Summary of Contents for Radical-7

Reviews:

Related manuals for Radical-7

Brands by name

Popular brands