Maserati MC20 2022 Owner'S Manual Download Page 184

Page: 184 / 288

180

Starting and Driving

(Continued)

will be displayed on the instrument
cluster.

Launch Control Sequence

NOTE:

• All the above mentioned conditions

must be verified in order to activate
"Launch Control" performance start
procedure.

• Each step displayed on the

instrument cluster has a time out
approximately of 5 seconds.

• "Launch Control" maneuver requires

to use both foot, left foot to brake
and right foot to accelerate at the
same time.

• With engine on, parking brake

disengaged, brake pedal pressed,
press Launch Control button on the
steering wheel.

The instrument cluster shows the
"LAUNCH ON" message.

• To confirm the "Launch Control"

sequence, press the brake pedal.
With brake pedal pressed with left
foot, fully press the accelerator pedal
(with right foot).

• Release brake pedal. The launch of

the vehicle starts with engine torque
calibrated to maximize performance.

• During the acceleration phase the

“Launch Control” symbol appears at

the bottom left of the main area of
the cluster display.

Conditions to Stop Launch
Control Sequence

The driver can interrupt the Launch
Control sequence in any moment
before starting:

NOTE:

• Removing foot from brake pedal,

even before accelerator full pressed.

• Changing gear, exiting from CORSA

drive mode, turning too much the
steering wheel or using the parking
brake.

• Waiting about 10 seconds without

accelerating.

• Waiting more than 5 seconds without

releasing the brake pedal after
acceleration pedal is pressed.

Summary of Contents for MC20 2022

































































































































































































































































































Search results

Summary of Contents for MC20 2022

Reviews:

Related manuals for MC20 2022

Brands by name

Popular brands

Maserati MC20 2022, Owner'S Manual

Search results

Summary of Contents for MC20 2022

Reviews:

Related manuals for MC20 2022

Brands by name

Popular brands