Maruyama BC2301RS Owner'S/Operator'S Manual Download Page 21

Page: 21 / 28

＿

Maintenance

Air Filter

Maintenance Interval

・

The air filter should be cleaned

daily

, or more often when

working in extremely dusty conditions.

・

Replace after every 100 hours of operation.

Air Filter Cleaning

1. Remove the filter cover and foam element.

2. Clean the foam element with warm, soapy water. Let the

element dry completely.

3. Apply a light coat of SAE 30 motor oil to the foam element

and squeeze out all excess oil.

4. Reassemble the foam element and filter cover.

Fuel Filter

Maintenance Interval

The fuel filter should be replaced after every 100 hours of

operation.

Fuel Filter Replacement

The fuel filter is attached to the end of the fuel pick-up hose

inside the tank.
To replace the fuel filter:

1. Make sure the fuel tank is empty.
2. Loosen the fuel tank cap, and pull up and remove the cap

holder.

3. Using a wire hook, gently pull the fuel filter out through the

fuel filler opening.

4. Grasp the fuel hose next to the fuel filter fitting and re-

move the filter, but do not release the hose.

5. While still holding on to fuel hose, attach the new fuel fil-

ter.

6. Drop the new fuel filter back into the fuel tank.
7. Make sure that the fuel filter is not stuck in a corner of the

tank, and that the fuel hose is not doubled over

(

kinked

)

before refueling.

Fuel Pick-up Hose

Wire

Fuel Filter

Cap Holder

Fuel Tank

Fuel Tank Cap

[BC2301RS, BC2601RS,

BC3021RS]

[BC4321H-RS]

Filter Cover

Knob

Foam Element

Summary of Contents for BC2301RS





























Search results

Summary of Contents for BC2301RS

Reviews:

Related manuals for BC2301RS

Brands by name

Popular brands

Maruyama BC2301RS, Owner'S/Operator'S Manual

Search results

Summary of Contents for BC2301RS

Reviews:

Related manuals for BC2301RS

Brands by name

Popular brands