Maruyama BC2301RS Owner'S/Operator'S Manual Download Page 17

Page: 17 / 28

＿

Trimmer Operation

CAUTION

Read the Safety instructions beginning on page 3 concerning proper use of the String Trimmer.

Always wear gloves and protective clothing when operating the String Trimmer.

Trimmer Operating Position

Before using the Trimmer, check the following:
1. The operator must be wearing the shoulder strap or shoulder harness

attached to the Trimmer, and the Trimmer should be on operator’s

right side.

[Model BC2301RS, BC2601RS, BC3021RS]

2. The operator’s right hand should be holding the shaft grip, with his or

her fingers on the throttle trigger. The right arm should be slightly

bent.

3. The left hand should be holding the loop handle with the fingers and

thumb fully enclosed around the grip. The left arm should be ex-

tended. Reposition the loop handle up or down the shaft assembly if

necessary for a comfortable position.

[Model BC4321H-RS]

2. The operator’s right hand should be holding the right-hand horn han-

dle grip, with the fingers on the throttle trigger.

3. The left hand should be holding the left-hand horn handle grip with the

fingers and thumb fully enclosed around the grip.

[All models]

4. The Trimmer weight should be evenly distributed between the arms.

The trimmer head should be near and parallel to the ground.

5. Accelerate and hold the engine at cutting speed before entering the

material to be cut.

6. Always release the throttle trigger and allow the engine to return to

idle speed when not cutting.

7. Stop the Trimmer engine when moving between work sites.

• If the trimmer head becomes jammed, stop the engine immediately.

• Make certain all moving parts have stopped and disconnect the spark

plug before inspecting the equipment for damage.

• Never use a String Trimmer that has a chipped, cracked or broken

trimmer head.

Shoulder Harness

[BC4321H-RS]

IMPORTANT: To detach the shoulder strap/

harness quickly from the

Trimmer, pull upward on the

Red Band/ Tab.

[BC2301RS, BC2601RS, BC3021RS]

Shoulder Strap

[BC2301RS, BC2601RS,

BC3021RS]

Red Band

Red Tab

Shoulder

Harness

Shoulder

Strap

Hook

Ring

Pull

Summary of Contents for BC2301RS





























Search results

Summary of Contents for BC2301RS

Reviews:

Related manuals for BC2301RS

Brands by name

Popular brands

Maruyama BC2301RS, Owner'S/Operator'S Manual

Search results

Summary of Contents for BC2301RS

Reviews:

Related manuals for BC2301RS

Brands by name

Popular brands