Maruyama BC2301RS Owner'S/Operator'S Manual Download Page 9

Page: 9 / 28

＿

[Model BC2301RS, BC2601RS, BC3021RS]

IMPORTANT: Make sure the trimmer head is for LEFT-

HAND ROTATION (counter-clockwise) as

viewed from the operator’s position, and

that the trimmer head adapter is a male,

M8 left-hand thread.

1. Remove the blade bolt and stabilizer from the attaching shaft

out of the gearcase. (Keep the blade bolt and stabilizer)

Note: The blade bolt has left-hand thread.

2. Align the hole in the boss adapter with the guide slot in

the gearcase.

3. Insert the Ø3,5mm pin into the hole in the boss adapter and

the guide slot in the gearcase to lock the attaching shaft.

4. Thread the trimmer head adapter into the attaching

shaft, then tighten the trimmer head by hand.

Note: The trimmer head adapter has left-hand thread.

5. Remove the Ø3,5mm pin from the boss adapter and

gearcase.

[Model

BC4321H-RS

]

IMPORTANT: Make sure the trimmer head is for LEFT-

HAND ROTATION (counter-clockwise) as

viewed from the operator’s position, and

that the trimmer head adapter is a female,

M10 left-hand thread.

1. Remove the blade nut and stabilizer from the attaching shaft

out of the gearcase. (Keep the blade nut and stabilizer )

Note: The blade nut has left-hand thread.

2. Align the hole in the boss adapter with the hole in the

gearcase.

3. Insert the Ø6 mm pin into the hole in the boss adapter

and the hole in the gearcase to lock the attaching shaft.

4. Thread the trimmer head adapter into the attaching

shaft, then tighten the trimmer head by hand.

Note: The trimmer head adapter has left-hand thread.

5. Remove the Ø6mm pin from the boss adapter and

gearcase.

Installing Cutting Attachment

Trimmer Head

POTENTIAL HAZARD

・

If the trimmer head is not adequately tightened, it can come loose from the Trimmer/

Brushcutter during use.

WHAT CAN HAPPEN

・

This may cause damage to property or personal injury.

HOW TO AVOID THE HAZARD

・

Make sure the trimmer head is securely fastened to the attaching shaft in the gearcase.

WARNING

Trimmer Head

Clamping

Washer

Holding Tool

(Ø3,5mm Pin)

Holding Tool

(Ø6mm Pin)

Gearcase

Left-hand

thread

Left-hand

thread

Attaching

Shaft

Boss

Adapter

Trimmer Head

Adapter

Trimmer Head

Adapter

[BC2301RS, BC2601RS, BC3021RS]

[

BC4321H-RS

]

Attaching

Shaft

Boss

Adapter

Clamping

Washer

Summary of Contents for BC2301RS





























Search results

Summary of Contents for BC2301RS

Reviews:

Related manuals for BC2301RS

Brands by name

Popular brands

Maruyama BC2301RS, Owner'S/Operator'S Manual

Search results

Summary of Contents for BC2301RS

Reviews:

Related manuals for BC2301RS

Brands by name

Popular brands