background image

8

Martin DMX 5.3 and RDM 5.5 Splitters user manual

Using for the first time 

Before applying power to the device: 
• Carefully review ”Safety information” starting on page 4.
• Check that the local AC mains power voltage is within the range given 

on the product’s serial number label.

• For the DMX 5.3 Splitter, if the supplied mains plug (cord cap) does not 

match your local power outlets, cut it off and install a suitable plug on 
the power cable (see ”Power cable and plug” on page 13).

• For the RDM 5.5 Splitter, install the supplied Neutrik PowerCon power 

input connector on a suitable power cable and either install a mains plug 
or hard-wire the device to a building electrical installation (see ”Power 
cable and plug” on page 14).

Functionality

Both the DMX 5.3 Splitter and RDM 5.5 Splitter transmit DMX signals. The 
RDM 5.5 Splitter also provides bidirectional transmission of an RDM 
signal on the data link.

Splitting the data link

Branching a DMX or DMX/RDM data link using a passive split such as a 
‘Y’ connector is likely to cause data transmission problems and is 
therefore not recommended. Martin Splitters allow the data link to be split 
into up to 5 branches:

without Splitter

with Splitter

not allowed

Figure 1: Splitting the data signal

Summary of Contents for DMX 5.3 Splitter





























Reviews: