manualshive.com logo in svg

Martel BETAGAUGE 330, Reference Manual

Share
Download
Martel BETAGAUGE 330 Reference Manual Download Page 47

BetaGauge 330 Ranges and Resolutions

Range (PSI)

30 PSI / 2.0 Bar 

150 PSI / 10 Bar 

300 PSI / 20 Bar 

Burst Pressure (PSI)

300

300

2000

Proof Pressure (PSI)

60

200

600

Engineering Unit

Factor

Psi

1

30.000

150.00

300.00

bar

0.06894757

2.0684

10.3421

20.684

mbar

68.94757

2068.4

10342.1

20684

kPa

6.894757

206.84

1034.21

2068.4

MPa

.00689476

0.2068

1.03421

2.0684

kg/cm2

0.07030697

2.1092

10.5460

21.092

cmH2O @ 4°C

70.3089

2109.3

10546.3

21093

cmH2O @ 20°C

70.4336

2113.0

10565.0

21130

mmH2O @ 4 °C

703.089

21093

N/A

N/A

mmH2O @ 20°C

704.336

21130

N/A

N/A

inH2O @ 4°C

27.68067

830.42

4152.1

8304.2

inH2O @ 20°C

27.72977

831.89

4159.5

8318.9

inH2O @ 60°F

27.70759

831.23

4156.1

8312.3

mmHg @ 0°C

51.71508

1551.5

7757.3

15515

inHg @ 0°C

2.03602

61.081

305.40

610.81

• Proof pressure - maximum allowable pressure without a shift in calibration

• Burst pressure - sensor damaged or destroyed; some risk of personnel injury

• Absolute ranges - the data for the 30 PSI / 2.0 Bar, 150 PSI / 10 Bar and 300 PSI / 20 Bar ranges also applies to the

absolute pressure versions of those ranges.

Summary of Contents for BETAGAUGE 330

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands