manualshive.com logo in svg

Martel BETAGAUGE 330, Reference Manual

Share
Download
Martel BETAGAUGE 330 Reference Manual Download Page 42

40

PT385_100;

PT392_100;

PTJIS_100;

CUSTOM;

For Example:

RTD_TYPE PT385_100 sets RTD type to PT100-385

RTD_TYPE

?

Returns the RTD type. 

For Example:

If the RTD type is PT385_100,  RTD_TYPE? Will return PT100_385. 

SIM

Sets the output for current simulation. This command also switches the calibrator into
mA simulation mode. A number and a unit must be entered after the command. 

For example:

SIM 5 MA sets the current simulation at 5 mA

SIM?

Returns the output of the current simulation. With the example above, the output
would be: 5.000000E-03, A

ST_START

Starts a switch test.

ST_CLOSE?

Returns the pressure that the switch closed at in the current pressure units.

ST_OPEN?

Returns the pressure that the switch opened at in the current pressure units.

ST_DEAD?

Returns deadband of the switch in the current pressure units.

TEMP_UNIT

This command is used to set the temperature unit used when measuring
temperature.

The first argument indicates which display to apply the change to.  The second
argument is the unit, either CEL for Celsius or FAR for fahrenheit.

For example:

To set the temperature unit to fahrenheit on the lower display send TEMP_UNIT
LOWER, FAR.

Summary of Contents for BETAGAUGE 330

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands