manualshive.com logo in svg

Martel BETAGAUGE 330, Reference Manual

Share
Download
Martel BETAGAUGE 330 Reference Manual Download Page 40

38

IO_STATE?

Returns the input/output/simulate state of the mA function of the calibrator.  

For example:

If the calibrator was in mA simulate mode IO_STATE? Would return SIM.

LOCAL

Restores the calibrator to local operation if it was in remote mode. Also clears
LOCKOUT if the calibrator was in lockout mode.

LOCKOUT

Sending this command sets the lockout state, when the unit is in REMOTE or goes to
remote it prohibits use of the keypad completely.  The lockout state can only be
cleared by sending the LOCAL command.

LO_ERR

Sets the 0% point for the percent error mode calculation in the current engineering
units.

For example:

To set the 0% point to 20 psi send LO_ERR 20.

LO_ERR?

Returns the 0% point for the percent error mode calculation. 

For example:

If the 0% point is set to 20 psi, LO_ERR? would return 2.01, PSI .

MOTOR_ON

Turns the motor on.

MOTOR_OFF

Turns the motor off.

MOTOR?

Returns the state of the motor. 

For example: 

If the motor was on MOTOR? Would return ON.

OHMS?

Returns the raw Ohm value from the RTD. 

Summary of Contents for BETAGAUGE 330

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands