background image

8

Rear Panel Features

SDI Inputs / Outputs and DVI-I Input

The V-R185-DLW has two 3G-SDI inputs and two active loop-
through outputs. SDI 1 and SDI 2 can be used simultaneously

to display Dual Link SDI signals. The DVI-I Input Connector
includes EDID and HDCP for connection to computers, DVD
Players, Rasterizers, etc.

Power Input

Connect the 4-pin XLR power input connector here. Power
should only be supplied from the included power supply.
IMPORTANT: If using a power source other than the included

power supply, damage may result. Please use the pin out
diagram in the

Specifications

section.

Tally Input / GPI Connector

The LED tally can be activated via the

HD-15 connector

by

connecting the corresponding pin to ground. A variety of
external devices can be used to perform the contact closure.
The HD-15 connector can also be used as a GPI port by
changing the settings in the On Screen Menu. No additional

power should be supplied to the HD-15 port.

RS-422/RS-485 Serial Interface

The RS-422/485 ports are used to remotely control the IMD or
all DLW features. (Note: Connector/pin-out may need to be

adapted depending on the protocol and controlling device
used). Only one connection to either port is needed to control
the monitor. The second port can be used to loop multiple

monitors in the same bus.

VESA Hole Pattern

VESA-standard 75mm hole-patters are provided to accomdate
a variety of custom mounting options.

29

Summary of Contents for V-R185-DLW



















Reviews: