background image

OWNER’S MANUAL 

 

MODEL HST13 – AUTOTOAST™ VERTICAL TOASTER     
                              

  

 

135168CH7 RV031308 
Copyright 

©

 2008  Marshall Air Systems, Inc. 

All Rights Reserved. 

 

ILLUSTRATIONS (CONTINUED)

 

 
 
WIRING SCHEMATIC (240V, 60HZ, 1PH) DOMESTIC VARIABLE SPEED.......................... DWG #143857  

 

WIRING SCHEMATIC (240V, 50/60Hz, 1 PH) SINGLE SPEED………………………………..DWG #142426

  

 
WIRING SCHEMATIC (220V, 50/60Hz, 1PH) SINGLE SPEED(ECM CONTROL) ................ DWG #144562

 

 
WIRING SCHEMATIC (220V, 50/60Hz, 1PH) SINGLE SPEED (LED CONTROL) ................ DWG #144577 
 
WIRING SCHEMATIC (220-240V, 50/60Hz, 1PH) VARIABLE SPEED (LED CONTROL)..... DWG #145737 

 
SCHEMATICS FOR UNITS S/N 0928 AND BEFORE 

 
WIRING SCHEMATIC (208V, 50/60Hz, 1PH) ......................................................................... DWG #135169 
 
WIRING SCHEMATIC (240V, 50/60Hz, 1PH) CE ................................................................... DWG #135817

 

 
WIRING SCHEMATIC (240V, 50/60Hz, 1PH) DOMESTIC ..................................................... DWG #143180 
 
WIRING SCHEMATIC (240V, 50/60Hz, 1PH) ......................................................................... DWG #138828  
 
WIRING SCHEMATIC (208V, 50/60Hz, 1PH)SINGLE SPEED….…………………………..….DWG #141334 
 
WIRING SCHEMATIC (208V, 50/60Hz, 1PH)VARIABLE SPEED…………………………  ….DWG #145294 

 

 

 

Summary of Contents for AUTOTOAST HST13S





























Reviews: