background image

A

Auxiliary Panel(s)........................... 11

C

Celsius ......................................... 2, 12
Circulation......................................7
Cleanup Cycle.......................1, 2, 9, 13
Current Water Temperature........ 1

D

Display.....................................1, 3, 4, 5

E

Exiting Screens.............................. 5

F

Fahrenheit...................................2, 12
Fatal Error ....................................... 2
Fault Log........................................ 12
Filter ................................................ 1, 2
Filter Cycle................................. 9, 10
Flip Screen.................................2, 3, 5
Flow-Related Checks.................. 16
Freeze Protection................. 9, 15, 16

G

GFCI Test............................... 12, 14, 17

H

Heat Indicator. ................................1
Heat Mode....................................6, 7
High Temperature Range ........1, 2
Hold ............................................ 3, 11

I

Information Message.................... 2
Invert ................................................. 2

J

Jet ................................2, 4, 7, 8, 9, 16

L

Language.......................................11
Light..................................1, 2, 3, 4, 5

M

Main Screen .......................1, 2, 3, 4
Messages ................................1, 2, 3
Message Waiting Indicator...... 1, 2
Music .........................................1, 2, 3

N

Navigation....................................... 3
Normal Error .................................. 2

O

Ozone ........................................ 2, 9

P

Page Up/Down.............................. 6
Panel Version .............................. 13
Polling ...........................................7, 9
Press-and-Hold............................. 3
Priming Mode........................5, 8, 12
Programming.................................. 6
Pumps ...................................9, 11, 15
Purge ........................................8, 9, 11

R

RCD .................................................14
Ready-in-Rest Mode ................... 7
Ready Mode ......................1, 2, 7, 9
Reminder Message..................2, 12
Rest Mode.............................2, 7, 11

S

Set Temperature.....................1, 2, 3
Set Temperature Lower................ 2
Set Temperture Higher................... 2
Settings.........................2, 3, 11, 13, 17
Settings Screen................6, 7, 10, 12
Spa Equipment Control............ 1, 2
Spa Screen.............................4, 9, 11
Spa Status. ......................................1
System Information...................2, 13

T

Temp Display ............................... 12
Temperature Range ...............1, 2, 3
Temperature Scale ....................... 2
Time-of-Day................................. 1, 10

U

Utilities.......................................12, 14

V

Values Increment/Decrement..... 5

W

Wi-Fi ............................................1, 2

INDEX

19

Summary of Contents for spaTouch2




















Reviews: