Marquis MQHBZDV3636 Page 5 Installation Instructions Manual Download

Page: 5 / 67

Mobile Home/Manufactured Housing Installation

This Direct Vent System Appliance must be installed in accordance with the manufacturer’s installation instructions and the

Manufactured Home Construction and Safety Standard Title 24 CFR, Part 3280, or the current Standard for Fire Safety Criteria for

Manufactured Home Installations, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240 MH Mobile Home Standard in

Canada.

THE VENTED GAS FIREPLACE HEATERS (ANSI Z21.88-2009) IN THIS MANUAL MAY BE INSTALLED IN MANUFACTURED

(MOBILE)HOMES AFTER FIRST SALE IN THE USA.

THE VENTED GAS FIREPLACE HEATERS (ANSI Z21.88-2009) IN THIS MANUAL MAY BE INSTALLED IN MANUFACTURED

(MOBILE) HOMES IN CANADA.

Please follow the current ANSI/NFPA 70 National Electrical Code in the USA and CAN/CSA C22.1 Canadian National

Electrical Code in Canada.

An appliance must be grounded to the steel chassis of the home with 8 ga. copper wire using a serrated or star washer to

penetrate paint or protective coating to insure grounding.

Use carriage bolt at the attachment point (see diagram above) to secure the appliance to the floor.

For required venting components see venting installation in appropriate section of this manual.

Certified for installation in a bedroom or bed/sitting room. In Canada must be installed with listed millivolt thermostat. In USA see local

codes.

Warning: Do not compromise the structural integrity of the manufactured home wall, floor

or ceiling, during installation of appliance or venting.

Summary of Contents for MQHBZDV3636




































































Search results

Summary of Contents for MQHBZDV3636

Reviews:

Related manuals for MQHBZDV3636

Brands by name

Popular brands

Marquis MQHBZDV3636, Installation Instructions Manual

Search results

Summary of Contents for MQHBZDV3636

Reviews:

Related manuals for MQHBZDV3636

Brands by name

Popular brands