background image

4

oil level placard must be adjusted so that its “full” mark is at the same eleva-
tion as the “full” mark on the side of the Geareducer case. Check oil lines 
to be sure there are no leaks. See 

Geareducer User Manual

 for oil filling 

procedure and list of recommended lubricants.

5–Rotate fan by hand to be sure of free rotation and ample tip clearance. See 

Fan User Manual.

6–Check motor insulation with a “Megger”. See Maintenance Section of Marley 

Electric Motor User Manual.

7–Lubricate the motor according to motor manufacturer’s instructions.
8–Test run each fan separately for a short time. Check for excessive vibration 

or unusual noise. If either is present, see Troubleshooting Guide on pages 
14 and 15 of this manual. Fan must rotate clockwise when viewed from 
above. Recheck Geareducer oil level.

9–Check functioning of make-up water supply.
10–Make sure the blowdown will carry the proper amount of water.

Starting Procedure

WATER SYSTEM

–Fill the cold water collection basin and circulating water 

system until the operating water level is reached. See Operation Section, below. 
Prime and start the circulating water pumps. Increase the flow of circulating 
water gradually to design water flow rate to avoid water hammer which could 
damage the distribution piping system.

Clean  the  sump  screens  several  times  during  the  first  weeks  of 
operation. After this, clean sump screens weekly.

When starting in cold weather, follow procedures outlined in Cold 
Weather Operation.

STARTING FAN

–Start the fan. After 30 minutes of operating time to permit 

Geareducer oil to come up to operating temperature, check motor load with 
watt meter, or take operating volt and ampere readings and calculate motor 
hp. Refer to 

Marley Fan User Manual

 for instructions. Pitch fans to pull cor-

rect contract horsepower when circulating design water rate at design hot 
water temperature.

Operation

Entering  water  temperature  in  excess  of  125°F  may  result  in  fill 
deformation.

Note

Note

 

Caution

Summary of Contents for Marley Class F400





















Reviews: