manualshive.com logo in svg

Markusson Triplematic, Original Instruction Manual, Page: 36 / 48

Share
Download
Markusson Triplematic Original Instruction Manual Download Page 36

Maintenance and Service

Triplematic

36 Triplematic 201708 EN  

•  clockwise to set the first depth gauge by 

hand using the Markusson flat file and depth 

gauge tool.

•  clockwise to increase the height of the depth 

gauge (and therefore grind less of it), or

•  counter clockwise to decrease the height of 

the depth gauge (and therefore grind more 

of it).

4.  Repeat the sharpening test until the height of 

the depth gauges is correct.

6.5  Adjust the chain lock

NOTE: This instruction is for .404 chain pitch. For 

other chain pitches, adjust to lower numbers. The 

chain lock needs to be adjusted if the chain is not 

fixed during sharpening. 

1.  Lift the grinding head to its most upright 

position. 

  CAUTION Make sure that the grinding wheel 

is turned off.

2.  Set the chain pusher switch to ON (A). When 

the chain pusher starts moving forward, the 

chain vise is in its UN-LOCKED position (C). 

Set the chain pusher switch to OFF (D).

A

B

C

D

3.  Make sure that the groove in the chain vise is 

approximately  1,5 mm. Insert the feeler gauge 

. Adjust the nuts if necessary to adjust the chain 

vise so the feeler gauge can slide out. 

1.5 mm

4.  Set the chain pusher switch to ON (1). When 

the chain pusher is in its rear position, the chain 

vise is in its LOCKED position (2). Set the chain 

pusher switch to OFF (3).

5.  Make sure  that the groove in the chain vise is 

between 6mm - 8mm. 

6.  If the groove is not between 6mm - 8mm wide, 

turn the nut (A) in 1-1.5 turns clockwise, until 

the groove in the chain vise is between 6mm - 

8mm.

0.15-0.30mm

A

Summary of Contents for Triplematic

















































Reviews:

No comments