background image

16

17

Please follow these instructions for proper regular care each time the
Magnum media is serviced:

1. Shut down system and remove Canister.

2. Change media:

CARBON/MEDIA CONTAINER

Remove media and rinse container thoroughly. Refill container
with Black Diamond Activated Carbon and 

rinse carbon 

thoroughly.

Rinse or replace Rite-Size Filter Sleeve.

Environmental Tip

...Used activated carbon can be added to garden soil to aid

in plant fertilization (does not apply to media used with fish medications).

MICRON CARTRIDGE

Remove and clean Cartridge – 

never brush or machine wash.

Rinse off all visible dirt. Mix a solution of one part chlorine 
bleach to three parts water. Immerse cartridge completely in 
solution and soak overnight. Rinse thoroughly until chlorine 
smell disappears.

For Best Results

...Purchase a second Micron Cartridge for alternate use while

original Cartridge soaks and dries thoroughly.

3. Clean Canister thoroughly, especially sump area.
4. Clean Impeller Assembly and inspect for wear and smooth 

rotation. If excess wear is noted, replace worn parts immediately.

6. Gently clean flat Rubber Gaskets with warm water only.  
7. Wash O-Ring Seating Area on Canister and Cover.Wet O-Ring

before reinstalling.

8. Reassemble system and return to operation as previously instructed.

CAUTION: 

IF YOU HAVE INSTALLED QUICK DISCONNECT VALVES…

always close all valves before disconnecting.

!

MAGNUM QUICK DISCONNECT VALVES

Installation/Operation/Maintenance

Magnum Quick Disconnect Double Valves are featured as standard equipment
with the Magnum 350 Deluxe Convertible Canister Filter and Magnum 350
PRO System. Single and Double Valves may be purchased separately for use
with the Magnum 220 (1/2” Valves) and 350 (5/8” Valves).

INSTALLATION

Install 

Valves 

after completing hose installation (Figure 19). 

Begin installation on hoses leading from top of 

Magnum Canister

.

Choose convenient, easily accessible location along tubes for valves.
Cut and remove 5” of hose where valves are to be installed.

NOTE: 

If installing Single Valves make sure the ON/OFF Flow

Regulator is located on the Upper Hose Section.

Figure 19

Upper

Hose to

Aquarium

Lower

Hose to

Magnum

Compression 

Nut

Lock

Compression 

Nut

Coupling

Barrel

ON/OFF or FLOW

REGULATOR

ON/OFF or

FLOW REGULATOR

Double Valves Shown

On

Position

Off

Position

Off

Position

Summary of Contents for Magnum 220













Reviews: