background image

WARRANTY

(For the Original Owner Only)

(For Warranty Information, Please Mail to Manufacturer.)

Customer’s Name :   
Address :  
Phone : 

Unit

Serial # :
Model # :
Date Purchased :    
Installer’s Name : 

K-Star Pool/Spa Heater is guaranteed for a period of one year from the date
of its purchase to the original owner against any manufacturing defects.
Exception: factory installed heating elements carry a 90 day limited 
manufacturer warranty from date of heater installation only.

Any warranty claim must be pre-authorized by Consolidated Pool & Spa
Industries Inc. and claim must include: Model number, Serial number and
Date of purchase. Any defective unit shall be returned freight prepaid only.
Consolidated Pool & Spa Industries Inc. will not be responsible for
disconnection-reconnection charges.

The above warranty shall be considered void if:

i. 

The installation instructions are not followed.

ii. 

Unit is powered without any water circulation.

iii.  The power is disconnected and unit is not thoroughly drained at time of 

winterizing.

iv.  The Unit has been mishandled.
v. 

If corrosion of the unit’s internal parts occurs by unit being exposed to a 
salt water system, a system that uses salt to create a sanitizer or improper 
water chemistry (applies to all non-titanium heater models only). Warranty 
Registration must be done within ten days of purchase of the unit, by 
mailing warranty card below to:

361 Rowntree Dairy Road, Unit 4 
Woodbridge, ON L4L 8H1 Canada

Tel: 905.264.6496 Fax: 905.264.6508
Email:[email protected]

INSTRUCTION MANUAL

MODELS:

K-5-D / K-10-D / K-15-D
(Regular elements/digital Thermostat)

K-5-TT-D / K-10-TT-D / K-15-TT-D
(Titanium elements/digital Thermostat)

“K-STAR” DIGITAL

Electric Pool/Spa Heaters 

361 Rowntree Dairy Road, Unit 4 
Woodbridge, ON L4L 8H1 Canada

Tel: 905.264.6496 Fax: 905.264.6508
Email:[email protected]

Summary of Contents for K-5-D







Reviews: