Maretron MPOWER CLMD12 User Manual Download Page 29 | Manualshive

Page: 29 / 46

background image

Revision 1.6

Page 23

3.5.4.3.1 OnLevel(s)

This parameter allows you to configure the voltage level on the input signals that corresponds
to an ON status on the input as reported on the network. You can use any of the following
settings:

•

High

– a high voltage level on the input is represented as an ON value on the network.

A high impedance or a low voltage level on the input is represented as an OFF value on
the network.

•

Low

– a low voltage level on the input is represented as an ON value on the network. A

high impedance or a high voltage level on the input is represented as an OFF value on
the network.

•

Both

– a high voltage level or a low voltage level on the input is represented as an ON

value on the network. A high impedance on the input is represented as an OFF value on
the network.

3.5.4.3.2 State

This read-only field represents the current state of the input signal as reported on the network.

3.5.5 Advanced

The Advanced tab is used to configure and observe parameters that do not normally require
changing.

«
...
27
28
29
30
31
...
»

Summary of Contents for MPOWER CLMD12















































Reviews:

No comments

Related manuals for MPOWER CLMD12

Brand: ABB Pages: 139

Brand: ABB Pages: 28

Brand: ABB Pages: 59

Brand: Walchem Pages: 10

Brand: XGAMING Pages: 9

Brand: ZIMO Pages: 38

Brand: Banner Pages: 15

Brand: bar Pages: 2

Brand: GAUGEMASTER Pages: 2

Brand: EasyIO Pages: 19

Brand: Zero 88 Pages: 2

Brand: Zenit Pages: 24

Brand: PAC Pages: 17

Brand: VAT Pages: 39

Brand: Samson Pages: 124

Brand: Samson Pages: 86

Brand: VAC Pages: 5

Brand: Yngri Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands