Maretron MPOWER CLMD12 User Manual Download Page 46

Page: 46 / 46

CLMD12 User's Manual

Page A2

Appendix A

– NMEA 2000 Interfacing

Revision 1.5

3: Indicator #2

– This field indicates the state of the solid-state breaker on output channel

#2.

4: Indicator #3

– This field indicates the state of the solid-state breaker on output channel

#3.

5: Indicator #4

– This field indicates the state of the solid-state breaker on output channel

#4.

6: Indicator #5

– This field indicates the state of the solid-state breaker on output channel

#5.

7: Indicator #6

– This field indicates the state of the solid-state breaker on output channel

#6.

8: Indicator #7

– This field indicates the state of the solid-state breaker on output channel

#7.

9: Indicator #8

– This field indicates the state of the solid-state breaker on output channel

#8.

10: Indicator #9

– This field indicates the state of the solid-state breaker on output channel

#9.

11: Indicator #10

– This field indicates the state of the solid-state breaker on output channel

#10.

12: Indicator #11

– This field indicates the state of the solid-state breaker on output channel

#11.

13: Indicator #12

– This field indicates the state of the solid-state breaker on output channel

#12.

14: Indicator #13

– This field indicates the state sensed by the digital input on input channel

#1. The state will be one of the following values:

•

“OFF” – The digital input voltage level is outside the range(s) programmed for
“ON” levels

•

“ON” – The digital input voltage level is inside the range(s) programmed for
“ON” levels

Please refer to section 3.5.4.3.1 for details

15: Indicator #14

– This field indicates the state sensed by the digital input on input channel

#2.

16: Indicator #15

– This field indicates the state sensed by the digital input on input channel

#3.

17: Indicator #16

– This field indicates the state sensed by the digital input on input channel

#4.

18: Indicator #17

– This field indicates the state sensed by the digital input on input channel

#5.

19: Indicator #18

– This field indicates the state sensed by the digital input on input channel

#6.

20: Indicator #19

– This field indicates the state sensed by the digital input on input channel

#7.

Summary of Contents for MPOWER CLMD12















































Search results

Summary of Contents for MPOWER CLMD12

Reviews:

Related manuals for MPOWER CLMD12

Brands by name

Popular brands

Maretron MPOWER CLMD12, User Manual

Search results

Summary of Contents for MPOWER CLMD12

Reviews:

Related manuals for MPOWER CLMD12

Brands by name

Popular brands