ENGLISH
18
2. FUCTION SELECT & SURROUND MODE
When a function or surround mode button is selected:
VIDEO:
Displays the current video source. When DSS/TV, LD,
DVD, VCR or AUX is selected with the function selector,
both AUDIO and VIDEO shows the same name.
AUDIO:
Displays the current analog audio input source.
DIGITAL:
Displays the current digital input source.
SURR-MODE:
Displays the current Surround mode as follows;
AUTO, DOLBY, THX 5.1, THX Sur. EX , DTS CINEMA,
DTS MUSIC, HALL, MATRIX, MOVIE, 5-STEREO,
STEREO, MONO, S-DIRECT,
or
6CH-INPUT
.
3. MASTER VOLUME CONTROL
Displayed when the MASTER volume is varied or a button of the
remote handset is pressed.
The box display indicates the 0 dB level with a solid box “ ”.
4. MUTE
When the
MUTE
button is pressed on the remote control, “MUTE” will
be shown on screen. Pressing
MUTE
button again will clear the
display, or adjust the volume.
5.SLEEP TIMER
When the
SLEEP
button is pressed, the setting on or off and the
remaining time of the sleep timer function are displayed.
You can change the mode between on, off and the amount of time to
elapse before the unit will shut itself off by cycling the sleep button.
I
O
U
:
D
D
:
D E
D
O
I
L
I
A
G
T
I
V
A
D
:
D G – 5
D
V D
–
S U
R
R
M O D E
:
T
I
V
S C
–
I N E
D
L
L F E
E V E L
:
1 0
d B
–
MA
A
M S T E R
V O U M E
L
–
– – – –
– – – – – – –
– –
–
–
–
– – –
M U T E
S L E E P
T M E R
I
O N
9 0 m i n
BASIC OPERATION
LISTENING TO THE TUNER
Frequency scan step for AM is selectable. Default is 10 kHz step. If
your country’s standard is 9 kHz step, press “AM” button on the
remote more than 6 seconds. Scan step will change.
Note:
• Memory for the tuner will clear by this setup.
MANUAL TUNING
1.
To select the tuner as the source, turn the
INPUT SELECTOR
knob
!5
on the front panel or press the
Tuner
button on the remote.
2.
Press the
BAND
button
y
on the SR-14mk
II
or
AM/FM
buttons
on page of Tune mode on the remote to select the desired
frequency band.
3.
Press the
AUTO TUNING
button
!7
on the SR-14mk
II
to display
the frequency.
4.
Turn the
GYRO TUNING
knob
@1
on SR-14mk
II
or press
< , >
button on page of Control mode on the remote.
5.
If FM is selected, press the
FM MODE
button
u
on the front panel
or the
Mono
buttons on page of Tune mode on the remote to
select the desired audio mode.
AUTO TUNING (USING THE SR-14MK
II
)
Light up the “AUTO TUN” indicator by pressing the
AUTO TUNING
button
!7
and turn the
GYRO TUNING
knob
@1
.
AUTO TUNING (USING THE REMOTE CONTROL UNIT)
The
< , >
button is pressed for more than 1 second to start Auto
tuning function.
(FM) MODE Button Operation
When “AUTO” indicator is on in the display, FM stations which
broadcast in stereo will be received in stereo and the “STEREO”
indicator lights.
When “AUTO” indicator is off, all the FM stations will be received in
monaural regardless of whether or not they are broadcasting in
stereo.
PRESET TUNING
With this unit you can preset up to 50 FM/AM stations in any order.
For each station, you can memorize the frequency and reception
mode if desired.
1-a. Manual Presetting (Using the SR-14mk
II
)
1.
Refer to the “
MANUAL TUNING
” or “
AUTO TUNING
” section
above to tune in a desired station.
2.
Press the
MEMO
button
i
. “MEMO” indicator starts blinking on
the display. While “MEMO” is still blinking (approx. 5 seconds),
select the preset number by turning the
GYRO TUNING
knob
@1
,
then press the
MEMO
button again.
3.
When a number has been properly input, “MEMO” indicator
stops blinking and goes out. The station is now stored in the
specified preset memory location.
1-b. Manual Presetting (Using the remote unit)
1.
Tune in a desired station.
2.
Press the
M
button on page at Keypad mode.
3.
Enter the desired preset number with
ten keypad
on page of
Keypad mode.
* When entering a single digit number (2, for example), either
input “02” or just input “2” and wait for a few seconds.
* If a number other than 1-50 is entered by mistake, that number
flashes in the display to indicate that it is invalid and the display
returns to the original frequency display.
