Manson Engineering Industrial SBC-9138 User Manual Download Page 10

I.  Trouble Shooting 

 

PROBLEM 

INDICATIONS 

POSSIBLE CAUSES 

SUGGESTED SOLUTION 

Charger does not 
work   

LCD display not 
turn on   

No AC power 
 
AC input socket fuse blown   

Check AC connections are correct   
 
Replace with correct AC fuse by 
qualified electrician 

No DC output   

Output short circuit 
symbol displays 
 
 
 
Charger over 
temperature 
symbol displays 
 
Overload (OCP) 
symbol displays 
 
Reverse polarity 
symbol displays 
 
Fan stuck symbol 
displays 

Output short circuit   
 
 
 
 
Over temperature protection triggered   
 
 
 
Severe over loading charger 
 
 
Reverse polarity connection 
 
 
DC fan locked by foreign object or 
malfunction 

Check DC connections between 
charger and battery. Charger can auto 
reset if remove the fault within 20 
seconds. 
 
Check air intake vent at bottom of 
charger is blocked or not. Check 
charger ambient ventilation. 
 
Check battery AH capacity within 
recommended range 
 
Check for correct polarity 
 
 
Check DC fan 

Battery does not 
get full charge 

LCD displays work 
normally and 
sequentially   
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Bad battery connection   
 
 
Battery type select switch in wrong 
setting 
 
Battery capacity too large 
 
 
Ambient temperature too low   
 
 
 
Battery has damaged cell or battery is 
too old   
 
Wrong set the lower power level 

Check for loose contact, right cable 
size, cable integrity 
 
Recheck battery type and change to 
correct battery selection 
 
Make sure charger rating matches 
battery capacity 
 
Move battery to a room temperature 
location, or get an optional 
temperature sensor   
 
Replace battery 
 
 
Recheck the current selection switch 
(5) to correct right setting 

Long charging 
time, float curve 
does not come on 
even after 20 
hours charging 
time. 

Absorption curve 
remains display all 
the time   

Charger internal fault   

Return the charger to distributor to 
repair   

Bulk curve is 
display all the time

 

Bulk curve 
remains on all the 
time   

Wrong battery type selection 
 
 
 
Battery is excessively depleted and 
the soft charging is triggered     
 
 
 
 
Battery temperature too high 

Check charged battery label and 
change battery type selection to 
correct setting 
 
Recharge the battery after a day, if 
bulk light remains after several hours, 
the battery is most likely damaged and 
cannot accept charge. Replace 
battery. 
 
Use accessory temperature sensor 

 
 
 
 

Summary of Contents for SBC-9138












Reviews: