Manitowoc Q1060 Installation Use And Care Manual Download

Page: 16 / 48

Installation Instructions

Section 2

2-6

Part Number 000001759

Q460 - Q1090 Ice Machines

SELF CONTAINED ICE MACHINE

230/1/50

Remote Electrical Wiring Connections

REMOTE ICE MACHINE WITH SINGLE CIRCUIT
MODEL CONDENSER 230/1/50

Ice

Machine

Voltage Phase

Cycle

Air-Cooled

Remote

Maximum Fuse/

Circuit Breaker

Minimum Circuit

Amps

Maximum Fuse/

Circuit Breaker

Minimum Circuit

Amps

Q460

230/1/50

6.7

N/A

Q660

230/1/50

9.2

N/A

Q1060

230/1/50

15.6

14.6

Q1090

230/1/50

N/A

14.6

Warning

These diagrams are not intended to show proper

wire routing, wire sizing, disconnects, etc., only the

correct wire connections.All electrical work,

including wire routing and grounding, must conform

to local and national electrical codes.

GROUND

ICE MACHINE

CONNECTIONS

TO SEPARATE

FUSE/BREAKER.

DISCONNECT ALL

POLES.

SV1191

SINGLE CIRCUIT

REMOTE

CONDENSER

NOTE: FAN
MOTOR IS
220-240V

ICE

MACHINE

GROUND

TO SEPARATE

FUSE/BREAKER

(220-240).

DISCONNECT ALL

POLES.

SV1256

Summary of Contents for Q1060

















































Search results

Summary of Contents for Q1060

Reviews:

Related manuals for Q1060

Brands by name

Popular brands

Manitowoc Q1060, Installation Use And Care Manual

Search results

Summary of Contents for Q1060

Reviews:

Related manuals for Q1060

Brands by name

Popular brands