background image

Part Number 040005626 5/17

113

SEVERE SYSTEM CONTAMINATION CLEANUP 
PROCEDURE

1. Remove the refrigerant charge.
2. Remove the compressor.
3. Disassemble the harvest solenoid valve. If 

burnout deposits are found inside the valve, install 
a rebuild kit, and replace the TXV and head 
pressure control valve.

4. Wipe away any burnout deposits from suction and 

discharge lines at compressor.

5. Sweep through the open system with dry 

nitrogen.

6. Install a new compressor and new start 

components.

7. Install suction line filter-drier in front of 

compressor.

8. Install a new liquid line drier.
9. Follow the normal evacuation procedure, except 

replace the evacuation step with the following:

A. Pull vacuum to 1000 microns. Break the 

vacuum with dry nitrogen and sweep the 
system. Pressurize to a minimum of 5 psig.

B. Change the vacuum pump oil.

C. Pull vacuum to 500 microns. Break the 

vacuum with dry nitrogen and sweep the 
system. Pressurize to a minimum of 5 psig.

D. Change the vacuum pump oil.

E. Pull vacuum to 500 microns. Run the vacuum 

pump for 1 additional hour.

10. Charge the system with the proper refrigerant to 

the nameplate charge.

11. Operate the ice machine for one hour. Then, 

check the pressure drop across the suction line 
filter-drier.

A. If the pressure drop is less than 2 psig, the 

filter-drier should be adequate for complete 
cleanup.

B. If the pressure drop exceeds 2 psig, change 

the suction line filter-drier and the liquid line 
drier. Repeat until the pressure drop is 
acceptable.

12. Operate the ice machine for 48 – 72 hours. 

Replace the suction line and liquid line drier if 
necessary.

13. Follow normal evacuation procedures.

Summary of Contents for MD0420A





































































































































Reviews: