background image

18 

Part Number 000016662 Rev 00 4/21

Maintenance 

Section 4

Remedial Cleaning Procedure

This procedure allows in place descaling of all surfaces that 

come in contact with the water system. The ice machine 

requires disassembly and descaling/sanitizing a minimum 

of once every 6 months. The quality of your potable water 

supply may require more frequent cleaning intervals.

CLEAN BUTTON OPERATION

•  When the clean cycle is complete, default is to start ice 

making. The ice machine will shutoff at the end of the 

clean cycle, when the power button is pressed during the 

clean cycle.

•  The clean cycle is aborted when the clean button is 

pressed and held for 3 seconds.

•  If the curtain switch is open for more than 2 seconds, the 

clean cycle is paused until the curtain switch closes. 

•  Pressing and holding the clean button for 3 seconds will 

abort the clean cycle.

Step 1 

Press power after ice falls from the evaporator at 

the end of a harvest cycle. Or, press power and allow the ice 

to melt off the evaporator 

Step 2 

Remove all ice from the bin.

Step 3 

Prepare 4 oz (1/2 cup) of undiluted Manitowoc Ice 

Machine Descaler (part number 9405463 only) in a container 

that will fit easily under the lifted water curtain. 

Model

Amount of Descaler

USE0050

4 ounces (120 ml)

Step 4 

Press and hold the clean button for 3 seconds.

Step 5 

Wait until the water pump sprays water onto the 

evaporator(approximately 3 minutes) then add the prepared 

Manitowoc Descaler by lifting the water curtain and pouring 

directly into the spray area.

Step 6 

Press the power button to have the ice machine 

stop at the end of the clean cycle. The ice machine will 

automatically time out a ten minute cleaning cycle, 

followed by five rinse cycles and stop. This entire cycle lasts 

approximately 30 minutes.

Step 7 

Prepare 1/2 oz (1 tablespoon) of undiluted 

Manitowoc Ice Machine Sanitizer (part number 9405653 

only) in a container that will fit into the same area.

Model

Amount of Sanitizer

USE0050

1/2 Ounce (15ml)

Step 8 

Press and hold the clean button for 3 seconds.

Step 9 

Wait until the water pump sprays water onto 

the evaporator(approximately 3 minutes) then add the 

prepared Manitowoc Sanitizer by lifting the water curtain 

and pouring directly into the spray area. The ice machine will 

automatically time out a ten minute sanitizing cycle, followed 

by five rinse cycles. This entire cycle lasts approximately 30 

minutes. When the clean cycle is complete the ice machine 

will start a freeze cycle.

Step 10 

Mix a solution of 1/4 oz. (7.4 ml) of sanitizer and 

1/2 gallon (1.9 L) of water. Use a spray bottle, sponge or cloth 

to sanitize the bin. Rinsing is not required

Summary of Contents for CrystalCraft Premier



























Reviews: