Manitowoc b970 series Technician'S Handbook Download Page 66

Page: 66 / 264

Part Number STH025 8/12

Machine Info Menu

From the Main menu, ensure that Machine Info is

highlighted and press the Checkmark to view a list

including capacity, model number, IMH (Ice Machine

Head) serial number, condenser serial number,

warranty, installation date, date of manufacture and

software version. Use the Down arrow to highlight an

item and use the Checkmark to view the information.

Press the Left arrow to return to previous screens

Machine Info Menu

•

90/70 capacity

•

Model #

•

Ice Machine Head Serial #

•

Condenser Serial #

•

Warranty

• Machine
• Evaporator
• Compressor

•

Install Date

•

Manufacture Date

•

Main Control Board Software Version

•

Display Software Version

RESET PASSWORD TO FACTORY DEFAULTS

The password can be reset to the factory defaults

when required. The default factory password is 1234.

To reset the ice machine to factory defaults refer to

page 78.

Summary of Contents for b970 series









































































































































































































































































Search results

Summary of Contents for b970 series

Reviews:

Related manuals for b970 series

Brands by name

Popular brands

Manitowoc b970 series, Technician'S Handbook

Search results

Summary of Contents for b970 series

Reviews:

Related manuals for b970 series

Brands by name

Popular brands