Manitou Mezzer Expert Page 5 Service Manual Download

Page: 5 / 43

MEZZER SERVICE MANUAL

Below is a list of tools necessary for changing the travel on the Mezzer fork.

• Safety Glasses

• Nitrile Gloves

• Lint-Free Rags

• Torque Wrench (6-220 in-lb [0.7-25 Nm])

• 2mm Hex Wrench

• 8mm Hex Wrench

• 14mm Box End Wrench

• Shock Pump

• Cassette Lockring tool* (e.g. Park tool FR-5.2)

• 1” socket

• 8mm Socket *

• 24mm Socket *

• (Optional, replaces items above with*) Manitou Tool Kit - Manitou part

number 172-31133 (This includes the Manitou Cassette Tool, 8mm thin wall

socket, and flat ground 24mm socket)

• Travel Spacer kit 141-36713-K032

Below is a list of additional tools necessary for a full service of the Mezzer

fork.

• 11mm Socket (Pro Only)

• Plastic or non-marring pick

• Downhill tire lever or flat blade screwdriver

• 5wt Maxima Fork oil - Manitou part number 85-0023

• Semi-bath Oil, 5/40w Synthetic - Manitou part number 85-0022

• Slickoleum™ Grease

• Isopropyl alcohol

• 37mm seal install tool 172-37540-K002

• Cartridge Damper Bleed Kit 141-30694-K020 (Pro Only)

• 37mm seal kit 141-36713-K025 and Air piston Seal Kit 141-36713-K027

or Rebuild kit 141-36713-K026

REQUIRED TOOLS

Summary of Contents for Mezzer Expert












































Search results

Summary of Contents for Mezzer Expert

Reviews:

Related manuals for Mezzer Expert

Brands by name

Popular brands

Manitou Mezzer Expert, Service Manual

Search results

Summary of Contents for Mezzer Expert

Reviews:

Related manuals for Mezzer Expert

Brands by name

Popular brands