background image

 

 

 

Rev 7/23/2014 

704-663-0094                    

www.m7speed.com

                   [email protected] 

Page 1 of 11 

Ultimate MINI Performance 

M7 R56 Rear Diffuser Tunnels 

Installation Guide  

 

Thank you for your purchase! We hope you enjoy the enhanced performance and styling for your MINI brought 
to you only by the innovative minds of M7. 
 

PLEASE READ INSTALLATION MANUAL BEFORE INSTALLING PRODUCT. 

M7 Speed engineers and manufactures the highest quality and best fitting Mini Cooper accessories and 
performance parts available anywhere on Planet Earth!  Please inspect your parts when you receive them to 
verify everything is included and no damage has happened during shipment. 

Read these instructions completely 

BEFORE attempting to install this product. 

 If you are not confident you can do the work described or do not 

have the tools or skills necessary please contact a local M7 dealer (listed on or website 

www.m7speed.com

or a 

reputable local automotive accessory installation center to perform this work. We acknowledge not everything is 
perfect but we work very hard every day to improve our products and make installations easier.  If you have any 
comments please contact M7 Customer Service directly at 704-663-0094.  We encourage and welcome all 
criticism Good or Bad.  
Thank you again for your purchase – we appreciate your business. 
 

Every M7 product is packed with pride and care. Please see the checklist below of every part that is 
included for this product.  
 

Qty  Description 

 

 

Main Tunnels (Left & Right) 

Entry Tunnel Brackets (Left & Right) 

Front Entry Tunnels (Left & Right) 

Hardware Kit 

Center Wing 

 

 

Bumper Brackets (2 LS, 1 RS) 

 

 

Main Tunnel Brackets-Front (Left & Right) 

 

 

Summary of Contents for R56












Reviews: