background image

15

TROUBLE SHOOTING GUIDE

If you suspect there is a problem with your receiver, please check the following trouble shooting guide before 
calling a 

Manhattan

authorised service agent.

WARNING! Do  NOT  attempt  to  repair  the  receiver  yourself.    Tampering  with  the  receiver  may 
result in fatal electric shock and will invalidate your warranty

.

Symptoms --- Possible cause / solutions
Front  display  not  lit ---

Check that the mains lead is plugged into the power socket. Check that your TV is 

tuned for the correct  channel or is switched to correct AV input.

No  picture  or  sound  or any  menus  ---

No  signal.  Channel  is  scrambled.  The  antenna  is  not  in  correct 

position. Check LNB wire is not damaged or shorting. Check LNB may be faulty.  Unplug  receiver  from  power 
socket and retry.

Interference, on picture, using Modulator output ---

Local terrestrial TV interference. Switch the output 

channel to different one then re-tune your TV. Select the appropriate ‘TV Standard’ using TV Settings menu.

Bad picture with blocking or  frozen  ---

Signal weak or noisy. Check signal quality. Antenna not in correct 

position

Not responding to remote control ---

Check the batteries in your remote control. Replace with new.

You have lost or forgotten your password ---

Apply master password or contact your Manhattan dealer.

SPECIFICATI

TUNER

Input Connector

F-type IEC 169-24 Female

Frequency Range

950MHz to 2150MHz

Input Impedance

75 Ohm 

Signal Level

-25 to - 65 dBm

LNB Power & Polarization                                 Ve14V, Hori18V (600mA Max. with Overload Protection)
LNB Control            

22KHz … 4 KHz, Tone burst A/B and DiSEqC 1.2

22 KHz Tone Amplitude 

0.6Vpp (…0.2V)

Input Symbol Rate

1~45 Msps

FEC Decoder 

Auto, 1/2, 2/3, 3/4, 5/6, 7/8

SYSTEM

Transmission Standard

DVB MPEG-2 

Input Data Rate

Max 15Mb/s

Aspect Ratio

4:3, 16:9

Video Resolution

720 x 480 NTSC, 720 x 576 PAL

Audio Decoding

MPEG Layer 1 and 2

Audio Mode

Single channel / Dual Channel/Joint Stereo / Mono

Sampling Rate

32KHz, 44.1KHz, 48KHz, 96KHz,

COMMON INTERFACE

Slots

2 slots type 1 and type 2

PCMCIA

DVB Common Interface Standard

IRDETO EMBEDDED CI

Card Slot

1 Slot DVB Common Interface Standard

PVR READY                        

To fit 40 - 120 GB Hard Disk Drive

CONNECTORS

CVBS

1 PHONO RCA

Audio Output

2 x PHONO (L, R) / RCA

Digital Audio Output

1 PHONO RCA (S/P DIF)

+12V Output                                            1 PHONO RCA (+12Volts 100mA Max)

Data Interface

1 RS232 (Bit Rate: 115,200 baud Connector: 9-pin D-sub type)

RF connectors

75 Ohm IEC 169-2 Male/Female

RF MODULATOR

Frequency

60MHz to 72 MHz

Channel Range 

CH3 to CH4

TV standard

NTSC M

SPECIFICATIONS

Summary of Contents for Plaza ST 250

















Reviews: