background image

Page 25

Version 2023-06-15

Fire damper - FDMR

TPM 140/19

The fire dampers are suitable for installation in arbitrary
position in vertical and horizontal passages of fire separ-
ating  constructions.  The  damper  installation  procedures
must  be  done  so  that  all  load  transfer  from  the  fire
separating  constructions  to  the  damper  is  absolutely
excluded. Following air-conditioning duct must be suspen-
ded  or  supported  so  that  all  load  transfer  from  the
following duct to the fire damper is absolutely excluded.
The  gap  between  the  installed  damper  and  the  fire
separating  construction  must  be  perfectly  filled  with
approved material.

The damper must be installed so that the damper blade
(in  closed  position)  is  situated  in  the  fire  separating
construction - marked by the label BUILT-IN EDGE on the
damper  casing.  If  such  solution  is  not  possible,  the  duct
between the fire separating construction and the damper
blade must be protected according to the certified install-
ation method 

→ see pages 28 to 86

During  the  installation  and  plastering  process,  the
actuating  mechanism  must  be  protected  (covered)

against damage and pollution. The damper casing should
not be deformed during bricking in. Once the damper is
built  in,  the  damper  blade  should  not  grind  against  the
damper casing during opening or closing.

The distance between the fire damper and the construc-
tion  (wall,  ceiling)  must  be  75  mm  at  the  minimum,
according to EN 1366-2. If two or more dampers are to be
installed in one fire separating construction, the distance
between  adjacent  dampers  must  be  200  mm  at  the
minimum, according to EN 1366-2.

Fire dampers can be installed without following duct on
one  or  both  sides.  Installation  without  following  duct  is
only possible in vertical constructions. In this case, the fire
dampers  must  be  installed  with  cover  grilles  (additional
extension parts may be required due to overlapping of the
damper  blade 

→  see  page  24

).  The  damper  must  be

installed  so  that  the  activation  device  (thermal
fuse/thermoelectric activation device/smoke detector) is
located at the highest possible point of the damper (top
of the casing).

Minimum distance between the fire dampers and the construction

minimum distance 200 mm between dampers, according to EN 1366-2

minimum distance 75 mm between damper and construction (wall/ceiling), according to EN 1366-2

recommended minimum distance 150 mm necessary for access to the actuator

recommended minimum distance 250 mm necessary for access to the manual control

 200

X

 75

Y

 200

 75

X

Y

 7

5

 2

0

0

 7

5

X = recommended min. distance for actuator ≥ 150 mm
X = recommended min. distance for manual control ≥ 250 mm

Y = min. distance for actuator ≥ 200 mm acc. to EN 1366-2
Y = recommended min. distance for manual control ≥ 250 mm

IV. INSTALLATION

Placement and installation

Summary of Contents for FDMR






































































































Reviews: